Installation and Operation Instructions Before attempting to connect or operate this product, please read these instructions completely. VLRM58 and VLRM24 MIMO Wireless Solutions VLRM58........ Wireless 5.8GHz MIMO access point, 120Vac input (Power supply) 24Vdc PoE VLRM24......... Wireless 2.4GHz MIMO access point, 120Vac input (Power supply) 24Vdc PoE VLRM58 5.8 Receiver VLRM24 2.4 Receiver Moog Inc. Sensor and Surveillance Systems © 2014, Moog Inc.
IMPORTANT SAFEGUARDS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with damp cloth. 7 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER ( OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SEVICING TO QUALIFIED SERVICE PERSONNEL. Do not block any of the ventilation openings.
Product Warranty Registration Register Your Products Online www.moogS3.com/technical-support/product-registration Moog values your patronage. We are solely committed to providing you with the highest quality products and superior customer service. With 3-Year and 5-Year warranties (depending on the product purchased) we stand behind every product we sell. See full warranty details at www.moogS3.
Limited Warranty for Moog Products Moog - Decatur Operations, subsequently referred to as “Manufacturer,” warrants these products to be free from defects in material or workmanship as follows: PRODUCT CATEGORY PARTS \ LABOR All Enclosures and Electronics Five (5) Years Accessory Brackets Five (5) Years Controllers Three (3) Years Power Supplies / IR Illuminators Three (3) Years Poles / PolEvators / CamEvator Three (3) Years Warrior Series™ / Q-View™ Three (3) Years SView Series Three (3) Yea
Electrical Specifications English Contents of Box Power Supply: 24Vdc, .5A POE Supply Included Max Power Consumption: 6.5 Watts (2.4GHz) 8 Watts (5.8GHz) Power Method: Passive Power over Ethernet (pairs 4,5+; 7,8 return) VLRM24 An all pole main switch with a contact of at least 3mm in each pole shall be incorporated in the electrical installation of the building. Tools Required: .150” Flathead Screwdriver 7/16 Wrench or Socket 9/16 Wrench or Socket Español Fuente de alimentación: 24Vdc, fuente de .
Wireless Cabling Best Practice CAUTION: MUST USE SHIELDED CABLE / CONNECTOR Product Description The VLRM24/58 is a Wi-Fi Station with WPA and WPA2 supplicant support. It is specially designed to act as a Transparent Wireless Bridge that associates to a service provider and authenticates using 802.1x, if required, on start up.
1 When using directional antennae, the AP unit and client should be aimed toward each other. • Al usar las antenas direccionales, la unidad del AP y el cliente se deben estar dirigido hacia uno a. • À l'aide des antennes directrices, l'unité d'AP et le client devraient être visés vers l'un l'autre. • Wenn man Richtantennen verwendet, sollten die AP-Maßeinheit und der Klient in Richtung zu einander gezielt werden. • Ao usar antenas direcionais, a unidade do AP e o cliente devem ser apontados para se.
2.1 LED Description LED Color Status Description PWR Green On Power is on Off Power is off LAN Green On Ethernet is connected Off Ethernet is not connected Green On Wi-Fi Associated with an access point. The number of LED lights from “MIN” to” MAX” indicates the received signal strength level. Not associated with any access point.
3.1 Wireless Configuration Click on the Wireless tab on the configuration page. Note that the unit is set to a Wireless Mode of Access Point and the default SSID for the wireless network is set to UBNT. The default SSID can be changed by clicking in the SSID box, typing in the new SSID that is required, and clicking on the Change button at the bottom right hand corner of the window. 3.2 Wireless Security Options Encryption for the wireless link is also set from this page.
3.3 Complete the following steps to connect two VLRM58 units on the same wireless network using WDS. • Connect to the VLRM24/58 by opening a web browser and connecting to http://192.168.1.20. Login to the device using UBNT for the username and UNBT for the password. Click on the Network tab on the configuration page. Note that a static IP address of 192.168.1.20 has been assigned to the unit be default. The default IP address, subnet mask, and gateway can all be changed from this screen if needed.
3.5 Changing Wireless Mode Change the Wireless Mode to Access Point WDS. Place a check mark in the Auto box beside the selection. Connect to the second device and complete the proceeding steps. In most cases the units will connect to one another using the Auto mode. However this might not always be the case. If the units do not connect automatically then the MAC addresses for the devices will need to be entered into the WDS Peers section.
Wireless IP & Mac Address Form For your convenience and future reference, the following form has been included to record your wireless surveillance systems IP and Mac addresses. Once completed, remove the form from instruction packet and place in a secure place or inside the Moog wireless product. The information recorded will prove beneficial when servicing or expanding your wireless system. Camera # 1 IP Address 192.168.1.
