© 2011, Moog Videolarm, Inc. All Rights Reserved PFDW75C12N and PFDW75T12N IP Ready™ Series - Pressurized FusionDome™ www.videolarm.com Installation and Operation Instructions for the following models: Before attempting to connect or operate this product, please read these instructions completely. To be used with the 81-IN5481 Instruction Manual.
IMPORTANT SAFEGUARDS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with damp cloth. 7 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER ( OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SEVICING TO QUALIFIED SERVICE PERSONNEL. Do not block any of the ventilation openings.
Limited Warranty for Moog Videolarm Products Moog Videolarm warrants these products to be free from defects in material or workmanship as follows: PRODUCT CATEGORY PARTS \ LABOR All Enclosures and Electronics* Five Poles/PolEvators™/CamEvator Three (3) Years Warrior Series™/Q-View™/IR Illuminators Five (5) Years SView Series™ Five (5) Years **6 months if used in auto scan/tour operation Controllers Five (5) Years Power Supplies Five (5) Years EcoKit Three (3) Years Accessory Brackets F
PFD75C12N, PFD75T12N IP Ready Pressurized Network Housing IP Ready Pressurized Network Housing with 12Vdc input, wall or pendant mounting, heater & blowers, ready for standard IP PTZ cameras. ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY): ! Power 12Vdc, Class 2 Only Total Power: 22 watts (Excluding camera) Accessories (Heater/Blower): 22 watts Heater: 20 watts Blower: 2 watt NOTE: This unit is designed for operation in an upright position.
IMPORTANT SAFEGUARDS NOTE: The PFD75C12N is a pressurized enclosure. As such, certain care is required for the safe use of the product. 1. Inspect the enclosure upon opening the box. Make sure the unit was not damaged during shipping. Immediately replace domes that have been cracked or show any signs of damage. 2. Always use safety goggles when servicing the unit. 3. 4. ! Never use an unregulated gas supply to pressurize the enclosure. The valve should be regulated with a maximum of 10 psi output.
STANDARD INSTALLATION PROCEDURES INCLUDES MODEL: 4. Mount the WM20G to the wall (hardware not included). (Figure 3) WM20G 1. Choose an appropriate location on an outside wall to mount the WM20G. NOTE: Be sure that the wall is sturdy enough to support the combined weight of the bracket and housing. 2. Place the base against the wall, mark the location of the four mounting holes, remove the bracket and drill the mounting holes. Pull all wiring through the wall at this time (Figure 1). Figure 3 5.
MOUNTING THE HOUSING GENERAL INSTRUCTIONS 1. Mount the housing assembly to the mounting bracket and housing coupling. A safety cable is included to temporarily hold it while making wiring connections. Loop the safety cable over one of the set screws on the coupling and make the appropriate connections using the (2) screw-down connectors supplied. The PFD75C12N is setup with (1) power input. 1. Accessory Power (yellow and green wire) Housing Power requires 42 watts (excluding camera) A.
CALIBRATING UNITS WITH LOW PRESSURE SENSORS (Not supplied on 12Vdc units) The Low Pressure alarm uses and absolute pressure sensor and must be calibrated to the local altitude. To calibrate you must; power up the unit. The green LED located in the center of the camera bracket will turn on. After 30 seconds the LED will begin to blink. At that time momentarily press the red push button switch located next to the LED. LED will turn off indicating unit is calibrated. Calibration is now complete.
Exploded View for Replacement Parts 10 2 8 11 9 4 3 1 12 16 17 1 15 14 13 15 13 5 17 6 14 16 7 -9-
Replacement Parts List Part No. Description 1 RPPFDT02 Housing Top (Extended) 2 RPVL1938 Removable Pendent Coupling 3 RPVL1802 Plastic Rain Shroud 4 RPVL1795 Tank Valve Gasket 5 RP96RSORG11 Main O-ring 9.25" 6 RPPFDTR01 Trim Ring w/o Dome 7 RCPFD7 Clear Dome with sealing o-ring 7b RCTPFD7 Tinted Dome with sealing o-ring 8 RPPFDT03 Internal Sealing Bracket Assembly 9 RP96RSORG10 Small O-ring 4.
Product Registration/Warranty Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest quality products available and superior customer service. Should a problem arise, rest assure that Moog Videolarm stands behind its products by offering impressive warranty plans: 3 Years on all Housings, Poles, Power Supplies, and Accessories and 5 Years on camera systems (SView, QView, Warriors), and InfraRed Illuminators.
