Operating instructions

ManualsBrandsMoog ManualsSecurity CamerasPFD75CF2N SERIES

Moog Inc.

Sensor and Surveillance Systems

3650 Woodhead Drive Northbrook, IL. USA 60062

+1.847.498.0700 Fax: +1.847.498.1258 www.moogS3.com

PFDW75CF2N

Pressurized FusionDome

™

Fixed Network Outdoor Wall Mounted Camera Enclosure

PFDW75CF2N............ Pressurized dome housing with WM20G gooseneck wall mount, clear dome, 24Vac input, heater and blower, (1) xed camera bracket

(7.5” MCL), 120 to 24Vac, 96W transformer

PFDW75TF2N............ Pressurized dome housing with WM20G gooseneck wall mount, tinted dome, 24Vac input, heater and blower, (1) xed camera bracket

(7.5” MCL), 120 to 24Vac, 96W transformer

Substitute “C” (Clear dome) for “T” (Tinted dome) version

Installation and Operation Instructions

Before attempting to connect or operate this product, please

read these instructions completely.

81-IN5369 111313

Summary of content (11 pages)

PAGE 1
Installation and Operation Instructions Before attempting to connect or operate this product, please read these instructions completely. PFDW75CF2N Pressurized FusionDome Fixed Network Outdoor Wall Mounted Camera Enclosure ™ PFDW75CF2N............ Pressurized dome housing with WM20G gooseneck wall mount, clear dome, 24Vac input, heater and blower, (1) fixed camera bracket (7.5” MCL), 120 to 24Vac, 96W transformer PFDW75TF2N............
PAGE 2
IMPORTANT SAFEGUARDS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with damp cloth. 7 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8 9 SAFETY PRECAUTIONS Cable Runs- All cable runs must be within permissible distance.
PAGE 3
Product Warranty Registration Register Your Products Online www.moogS3.com/technical-support/product-registration Moog values your patronage. We are solely committed to providing you with the highest quality products and superior customer service. With 3-Year and 5-Year warranties (depending on the product purchased) we stand behind every product we sell. See full warranty details at www.moogS3.
PAGE 4
Limited Warranty for Moog Products Moog - Decatur Operations, subsequently referred to as “Manufacturer,” warrants these products to be free from defects in material or workmanship as follows: PRODUCT CATEGORY PARTS \ LABOR All Enclosures and Electronics Five (5) Years Accessory Brackets Five (5) Years Controllers Three (3) Years Power Supplies / IR Illuminators Three (3) Years Poles / PolEvators / CamEvator Three (3) Years Warrior Series™ / Q-View™ Three (3) Years ™ Three (3) Years 6 months
PAGE 5
! English Electrical Specifications Power 24VAC Class 2 Only Contents of Box PFD75CF2N 24 VAC 3.3 Amps Total Power: 52 Watts Accessories: Heater: 50 Watts/Blower: 2 Watts Camera Power: 12VDC only; 18 Watts Max Tools Required: .100” Flat Head Screwdriver Phillips Head Screwdriver 7/16” Wrench or Socket 24 VAC 3.
PAGE 6
WM20G: SOLD SEPARATELY 12 2 1 SOLD SEPARATELY •Special anti-seize tape “DO NOT REMOVE” Teflon tape™ is wrapped around the pipe threads to ensure a tight seal and to prevent galling. • Cinta de Teflon ™ se envuelve alrededor de las roscas de la tubería para asegurar un sello hermético y para evitar el gripado. • Ruban téflon ™ est enroulé autour des filetages pour assurer une bonne étanchéité et éviter tout grippage.
PAGE 7
5 SOLD SEPARATELY Loop the lanyard over the screw head to temporarily hold housing. • Loop la cuerda de seguridad en la cabeza del tornillo para mantener temporalmente la vivienda. • Enroulez le cordon autour de la tête de vis pour maintenir temporairement le logement. • Loop the Lanyard über den Schraubenkopf vorübergehend zu halten Gehäuse. • Laço da corda sobre a cabeça do parafuso para reter temporariamente habitação.
PAGE 8
7 9 10 12 ,5 22 ,75 20 1,0 18 1,5 16 2,5 14 4 12 6 10 2 MM AWG 26 Watts Wiring the dome can be completed by referring to the diagram. • Atar con alambre la bóveda puede ser terminada refiriendo al diagrama. • Le câblage du dôme peut être accompli en se rapportant au diagramme. • Das Verdrahten der Haube kann durchgeführt werden, indem man auf das Diagramm sich bezieht. • Wiring a abóbada pode ser terminado consultando ao diagrama. • Legare la cupola può essere completato riferendosi allo schema.
PAGE 9
13 14 100 580 Fitting 50 0 150 Air Chuck 200 250 PSI 300 Hose Regulator Nitrogen Tank Hand tighten the screws on the dome. Recommended torque 12 inches/lb (1.35Nm). When pressurizing unit be sure to set the gauge or regulator from 10-20psi (.7-1.4bar). • La mano aprieta los tornillos en la bóveda. Esfuerzo de torsión recomendado 12 inches/lb (el 1.35Nm). • La main serrent les vis sur le dôme. Couple recommandé 12 inches/lb (1.35Nm). • Hand ziehen die Schrauben an der Haube fest.
PAGE 10
12 18 17 10 5 0 15 20 25 PSI 30 After purging check the housing pressure. It should be around 5psi (.34bar). • Después de purgar el cheque la presión de la cubierta. Debe estar alrededor de 5psi (34bar). • Après la purge du contrôle la pression de logement. Elle devrait être autour de 5psi (34bar). • Nachdem Überprüfung der Gehäusedruck bereinigt worden ist. Sie sollte um 5psi (34bar) sein. • Após ter removido a verificação a pressão da carcaça. Deve ser em torno de 5psi (34bar).
PAGE 11
1 Replacement Parts List FIXED PRESSURIZED HOUSING 2 4 3 6 1 5 7 9 8 17 10 19 11 15 14 13 16 12 18 20 20 19 18 N/S N/S N/S 17 16 15 14 13 12 11 10 9 8 7b 7 6 5 4 3 2 1 RP40BRTRAN3 RPFD060 RPRH713 RP46PKE1100 RP46PKH2200 RP40CAPPFD811 RPFD080 RPFD060 RPFD050 RP46PKH3063 RPFD072 RP95VALV07 RP95VALV08 RP70PT07a RP96RSORG10 RPPFDT03 RCTPFD7 RCPFD7 RPPFDTR01 RP96RSORG11 RPVL1795 RPVL1802 RPVL1938 RPPFDT02 Part No.