Product specifications

www.moogS3.com
PAN AND TILT CONFIGURATIONS
Moog pan and tilt models have been divided into several basic congurations:
1. Analog
2. IC: Integrated Control
3. ICM: Integrated Control Marine
4. ICMS: Integrated Control Marine Sentry
5. ICM – RF: Integrated Control Marine Radio Frequency
6. ICMS – RF: Integrated Control Marine Sentry Radio Frequency
Analog: All electrical power is delivered from the controller almost directly to the pan and tilt axis motors. There is one motor for each axis.
IC: Integrated Control (IC) includes electrical drivers from external controllers to inside the pan and tilt.
Marine: Pan and tilts are housed in rugged, welded, sealed enclosures that increase the range of its use to extreme and challenging environments. They are designed to
be used primarily in coastal, marine, frigid, humid, dirty, sandy, and salty atmospheres. (Note: Marine versions of the QPT-20 use extruded aluminum housings.)
Sentry: The Sentry designation refers to the use of higher reliability stepper motor technology. Stepper motor drives are used for applications where constant velocity, higher
dynamic range in rotational speed, torque, and incremental movement capability are required over that of the basic brush motor units.
RF: These units provide a means to pass RF signals through the body of the pan and tilt for continuous rotation applications.
PAN AND TILT WIRING AND CABLE CONFIGURATIONS
Formed Tabletop (FT): Basic tabletop; no payload interconnections going into or out of the pan and tilt to the payload.
Formed Tilt A (FTA): Formed tabletop with a single Mil-Spec I/O connector port located at the tilt axis. Pre-wired internal connections to this port allow the payload to
interface with the power, serial control, lens control, A/D conversion, and capabilities of the pan and tilt.
Formed Tilt B (FTB): Formed tabletop with Mil-Spec I/O connector port located at the tilt axis. Pre-wired I/O connections to this connector go directly to the base connector.
This allows the option to connect directly to the payload.
Universal: Wiring interface design incorporates multiple Mil-Spec connectors on the tabletop pre-wired for data, power and sensor control.
Single Ended Cables (SE): This cable conguration extends directly from the pan and tilt to the control point without any breakouts when the controller, power supply, and
video interfaces are co-located at the same point.
Bifurcated Cables (Bi): This conguration takes into consideration the fact that DC power, required by our IC based units, cannot be located as far away from the pan and
tilt as a control site can. Serially controlled pan and tilts, over copper wire, can be located as far as 4,000 ft. away using RS-422 / 485 formats. Ethernet based systems
can be located up to 328 ft. away without a switch.
TESTED AND CERTIFIED
Moog products have been qualied to the following performance levels:
Product
Repeatability
(Line of Sight)
Salt Spray Testing
MIL-STD-810F
Sand and Dust
Penetration (IP 6X)
Water Spray Penetration
(IP X6)
Temp Range
(Up to -40°C)
Vibration
(HMMWV)
Shock
(HMMWV)
GeminEye 0.25 deg Passed Passed Passed Passed Passed (8 lbs) Passed (8 lbs)
Apollo Class 0.05 deg Passed Passed Passed Passed Passed (50 lbs) Passed (50 lbs)
QPT-90 0.05 deg Passed Passed Passed Passed Passed (90 lbs) Passed (90 lbs)
QMP-R 0.05 deg Qualied by Similarity Passed Passed Passed Passed (150 lbs) Passed (150 lbs)
Abbreviated list of qualied products. Contact your sales rep for a full list.
AVAILABLE SYSTEM COLORS – STANDARD
Marine White – MWS*
Marine Navy Gray – MNG Flat Black – FB
37030 #
CARC Black – CBLK
Desert Tan – BGP
33446 #
CARC – Desert Tan – BGC
Olive Drab – OD
34084 #
CARC Green – GRN
* Unless otherwise noted MWS is the default nish
# Federal Standard 595B
Contact your sales rep for custom nishes and pricing
29
Pan and Tilt Positioners
Pan and Tilt Positioners
Unless Otherwise Noted, product falls under the jurisdiction of the United States Government under the EAR (Export Administration Regulations)
as EAR-99. Please contact our company Export Representative at [phone] for additional export information.