Operating instructions

ManualsBrandsMoog ManualsSecurity CamerasDeputyDome SERIES

- 1 -

www.videolarm.com

Installation and Operation Instructions for the following models:

DDW10CN2 DeputyDome™, Bullet-Resistant IP Camera System, PTZ and 26x Day/

Night Camera System features Heavy-Duty Metal Gear Pan/ Tilt. MPEG-4

and MJPEG video compression format, full D1. Clear dome, with 24Vac

input, heater/ blower Tough enough to stop a 9mm bullet

PDDW10CN2 (Pressurized Version)

DeputyDome™, Bullet-Resistant IP Camera System, PTZ and 26x Day/

Night Camera System features Heavy-Duty Metal Gear Pan/ Tilt. MPEG-4

and MJPEG video compression format, full D1. Clear dome, with 24Vac

input, heater/blower Tough enough to stop a 9mm bullet

Be fo re a tt em pt in g to c on ne ct o r op er at e th is p ro du ct ,p le as e re ad t he se i ns tr uc ti on s co mp le te ly.

81-IN5387

12-13-2011

D e p u t y D o m e ™

Bullet-Resistant IP Camera Housing

Summary of content (14 pages)

PAGE 1
©2011, Videolarm, Inc. All Rights Reserved DeputyDome™ Bullet-Resistant IP Camera Housing www.videolarm.com Installation and Operation Instructions for the following models: DDW10CN2 DeputyDome™, Bullet-Resistant IP Camera System, PTZ and 26x Day/ Night Camera System features Heavy-Duty Metal Gear Pan/ Tilt. MPEG-4 and MJPEG video compression format, full D1.
PAGE 2
IMPORTANT SAFEGUARDS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with damp cloth. 7 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER ( OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SEVICING TO QUALIFIED SERVICE PERSONNEL. Do not block any of the ventilation openings.
PAGE 3
Limited Warranty for Moog Videolarm Products Moog Videolarm warrants these products to be free from defects in material or workmanship as follows: PRODUCT CATEGORY PARTS \ LABOR All Enclosures and Electronics* Five Poles/PolEvators™/CamEvator Three (3) Years Warrior Series™/Q-View™/IR Illuminators Five (5) Years SView Series™ Five (5) Years **6 months if used in auto scan/tour operation Controllers Five (5) Years Power Supplies Five (5) Years EcoKit Three (3) Years Accessory Brackets F
PAGE 4
NOTE: WALL MOUNT INSTALLATION (cont.) The DeputyDome™ is packed in two separate boxes, one for the housing and one for the pan/tilt and bullet-resistant liner. Installation should be completed as follows: 1. Run wiring to the chosen location. 2. Detach the housing and mount the wall bracket. 3. Make wiring connections. 4. Complete wiring runs. 5. Install the pan/tilt and make necessary adjustments. 6. Install the bullet-resistant liner. 7. Attach the housing and ome.
PAGE 5
CAUTION: Using smaller than recommended cable sizes can result in poor performance and damage to the heater and camera. Wiring Chart Non-Pressurized Receiver Version A. Heater 1) Red - Heater 1 2) N/C 3) Red - Heater B. Camera Power 1) Black - V2 2) Orange - V1 C. RJ45 Wire Gauge VA 22 70 25ft 7m 20 40 ft 14 m 18 64 ft 20 m 16 100 ft 30 m 14 162 ft 50 m 12 260 ft 80 m INSTALLING THE PAN/TILT 1. Slide the pan/tilt back into place.
PAGE 6
. The liner should still be able to move up by about 1/16" on an inch to allow the liner to move when shot and transfer the force to the housing instead of the pan/tilt. REATTACHING THE DOME ON PRESSURIZED UNITS 1. The dome on the pressurized unit must be attached correctly for the unit to function properly. All screws and posts must line up exactly. INSTALLING THE HOUSING ON THE BRACKET 1.
PAGE 7
IP Instructions The factory default IP adress is 192.168.0.200. See IP Ready camera instruction for installation details. For Pan/Tilt control click on PTZ control icon in top right corner. Pan/Tilt control contains standard pan/tilt/camera control functions. To save preset, pull down #1 preset, move camera to desired position and then hit "save" to save preset. You can store up to 18 presets. Adjusting "speed" setting will correspondingly adjust dwell time when the preset is saved.
PAGE 8
PROCEDURES FOR PRESSURIZED HOUSINGS Filling and Refilling Pressurized housings provide maximum protection for CCTV cameras and lenses. The charge of dry nitrogen inside the housing eliminates the effects of moisture, dust, insects and corrosive exhaust fumes. This allows a longer lifetime for your surveillance equipment. To fill (or refill) a pressurized housing, you must have the following: 1. Attach the barb to the regulator. 2. Remove the cap from the Schraeder valve. 3.
PAGE 9
Exploded View for Replacement Parts 2 1 3 8 4 5 9 6 7 11 10 12 13 13 15 82 16 81 17 19 18 20 22 21 -9-
PAGE 10
Exploded View for Replacement Parts (Pan/Tilt Assembly) 25 26 27 28 29 30 31 - 10 -
PAGE 11
Exploded View for Replacement Parts (Pan Bearing Assembly) 35 37 36 38 39 40 - 11 -
PAGE 12
Exploded View for Replacement Parts (Network Assembly) 81 81 81 16 82 - 12 -
PAGE 13
Replacement Parts List Part No. Description 1 91-NTFL01 3/8-16 Flange Nut (4) 2 90-BTSEC06 1/4-20 x 1/2" Security screw SS (2) 3 50-VL1428 DDWC10 housing body 4 30-VL1405 DDWC10 accs mounting bracket 5 92-WSFL01 1/4 Flat Washer SS (4) 6 92-WSSL01 1/4 Split Lockwasher SS (4) 7 90-BTHH32 1/4-20 x 1/2" Hex head bolt SS (4) 8 90-BTRP31 8-32 x 3/8" Grounding screw 9 71-BLEH24 Blower, 24VDC 60MM 10 70-WPTRAN/P2 240/120V: 1.
PAGE 14
Product Registration/Warranty Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest quality products available and superior customer service. Should a problem arise, rest assure that Moog Videolarm stands behind its products by offering impressive warranty plans: 3 Years on all Housings, Poles, Power Supplies, and Accessories and 5 Years on camera systems (SView, QView, Warriors), and InfraRed Illuminators.