© 2009-2010, Moog Videolarm, Inc. All Rights Reserved © 2009-2010, Videolarm, Inc. All Right Reserved Product Information for IP Ready Software | 1. 8 0 0 . 5 5 4 .112 4 | w w w.v ide o lar m .com Deputy Dome Bullet-Resistant Standard / Pressurized Dome www.videolarm.
IMPORTANT SAFEGUARDS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with damp cloth. 7 Do not block any of the ventilation openings. Install in accordance with the SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN manufacturers instructions. 8 Cable Runs- All cable runs must be within permissible distance.
LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship,as follows: PRODUCTCATEGORY PARTS LABOR All Enclosuresand Electronics Five (5) Years Five (5) Years Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan /tour operation Poles/PoleEvators Three (3) Years /tour operation Three (3) Years Warrior/Q-View/I.R.
! Electrical Specifications (Camera with hardwire pan/tilt) Power Source & Power Consumption (includes: heater, blower and camera) DDW10CR PDDW10CR DDW10CR1 (N) DDW10CR2 (N) English 115 VAC, 90 vA, 0.8 Amps 24 VAC, (Class 2), 90 vA, 3.75Amps (N) Network model CAMERA SPECIFICATIONS Resolution - 470 TVL - NTSC, 460TVL - PAL Minimum Illumination - 1.0 1.0 Lux Zoom Ratio - 26x, 3.
1 Remove (2) tamper resistant with the security tool provided in the packet. 2 Loosen all flange nuts and turn the housing clockwise to remove the housing from the mount. The wall mount can now be attached to the wall. • Quite (2) a pisón resistente con la herramienta de la seguridad proporcionada en el paquete. • • Enlevez (2) le bourreur résistant avec l'outil de sécurité fourni dans le paquet.
5 A 6 3 2 1 B 2 1 C 4 3 2 1 D 6 5 4 3 2 1 E or Wiring Chart Non-Pressurized Receiver Version A. Heater 1) Red - Heater 1 2) N/C 3) Red - Heater B. Camera Power 1) Black - V2 2) Orange - V1 C. Lens ANALOG/ IP 1) Blue - Alarm Input 1 2) Violet - Alarm Input 2 3) Gray - Alarm Input 3 4) White - Alarm common D. Pan/Tilt 1) Gray - RXA 2) Pink - N/C 3) Tan - TXA 4) Green - RXB 5) Brown - N/C 6) Blue - TXB E. BNC 1(NETWORK IP) F.Green Housing Ground (not shown) 24VAC 115VAC 2.4A .5A (58W) 1.
8 9 To remove Pan/Tilt assembly rmove the dome and liner • Para eliminar Pan / Inclinación rmove montaje de la cúpula y de línea • Pour supprimer Pan / Tilt rmove montage du dôme et doublure • So entfernen Sie Pan / Tilt rmove Montage der Kuppel und Linienkonferenzen • Para remover Pan / Tilt rmove montagem da cúpula e forro Loosen captive bolt as shown • Afloje el perno cautivo, como se muestra • Desserrez pistolet comme le montre • Lösen Sie Bolzenschuss wie • Afrouxe bolter cativeiro como mostrado • A
12 NOTE Position 13 Align O Ring To attach dome inserts most align properly with housing • Para adjuntar cúpula alinear correctamente la mayoría de las inserciones de la vivienda • Pour joindre la plupart des inserts dôme aligner correctement avec le logement • So hängen die meisten Einsätze Kuppel Angleichung richtig mit Gehäuse Align insert and install dome • Alinear insertar e instalar cúpula • Alignez et installez insérer dôme • Richten Sie einfügen und installieren Kuppel • Alinhar inserir e inst
16 100 580 Fitting 50 0 150 Air Chuck 200 250 PSI 300 17 Hose Regulator Nitrogen Tank When pressurizing unit be sure to set the guage or regulator from 10-20psi (.7-1.4bar). • Al presurizar la unidad sea seguro fijar la medida o el regulador de 10-20psi (7-1.4bar). • En pressurisant l'unité soyez sûr de placer la jauge ou le régulateur de 10-20psi (7-1.4bar). • Wenn Sie Maßeinheit unter Druck setzen, seien Sie sicher, das Eichmaß oder den Regler von 10-20psi (7-1.4bar) einzustellen.
20 CHANGING SETTINGS FOR RECEIVER / DRIVER UNITS Dipswitches DIPSWITCHES The dipswitches serve a dual purpose. First, they control the address of the pan/tilt when operated via RS485. Second, they control the alarm and display functions for the pan/tilt. Address changes are made using the dip switches located on the PC board.
UNIT PARAMETERS 22 23 Alarm sense, camera on-screen display and baud rate can all be controlled by the dipswitches. The alarm sense can be set to accept either contact closures (NO) or contact openings (NC) as the alarm condition. The camera on-screen display will show icons on the monitor when zoom, focus, and iris are used. Factory presets are contact closures for the alarm sense, "off" for the camera on-screen display, and 9600 baud.
Replacement Parts List DDW10CR / PDDW10CR 1 25 2 3 26 27 4 5 28 6 7 29 8 9 10 11 12 13 30 14 15 16 17 31 18 19 20 21 22 1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 17 18 19 20 21 22 25 26 27 28 29 30 31 35 36 37 38 39 40 41 Part Number Description Qty. Part Number Description Qty.
35 58 59 60 61 62 36 37 38 66 65 64 39 63 67 40 41 42 43 44 45 46 47 48 49 50 51 68 69 70 52 53 54 55 79 56 57 78 77 76 75
VL-422 Communication Protocol (DeputyDome) 1 Message Format Data is transmitted at 9600 baud, 1 start bit, 1 stop bit, 8 data bits (lsb first), no parity. The general format for messages sent to the DeputyDome and for inquiry response messages sent by the DeputyDome is shown below: BYTE DATA DESCRIPTION 1 F8H Sync character 2 Address in hex Camera address (01H – DFH) 3 to N-1 Command Data All command characters are 8-bit characters; most are ASCII characters.
3.2 Preset Command Messages These commands control the position presets and some of the operational parameters of the pan/tilt platform. Byte number 1 is the start of message “F8”, byte number 2 is the device address (default = 01), and byte number five is the message terminator byte. Note that preset 63 is reserved for another function; this preset number is used in the commands “P””?” and “H””?”.
7 E2 (MS nibble) 30H - 3FH Position data is 30H ored with data nibble E11, E10, E09, E08 of elevation data. 8 E1 30H - 3FH Position data is 30H ored with data nibble E07, E06, E05, E04 of elevation data. 9 E0 (LS nibble) 30H - 3FH Position data is 30H ored with data nibble E03, E02, E01, E00 of elevation data. 10 Terminator and Checksum 80H - 8FH Most significant bit is always 1.
BYTE DATA DESCRIPTION 1 F8H Sync character 2 Address in hex Camera address (01H - DFH) 3 “v” Lower case “v” 4 Z2 (MS nibble) 30H - 3FH Position data is 30H ored with data nibble Z11, Z10, Z09, Z08 of zoom lens position data. 5 Z1 30H - 3FH Position data is 30H ored with data nibble Z07, Z06, Z05, Z04 of zoom lens position data. 6 Z0 (LS nibble) 30H - 3FH Position data is 30H ored with data nibble Z03, Z02, Z01, Z00 of zoom lens position data.
6 Z0 (LS nibble) 30H - 3FH Position data is 30H ored with data nibble Z03, Z02, Z01, Z00 of zoom lens position data. 7 F2 (MS nibble) 30H - 3FH Position data is 30H ored with data nibble F11, F10, F09, F08 of focus data. 8 F1 30H - 3FH Position data is 30H ored with data nibble F07, F06, F05, F04 of focus data. 9 F0 (LS nibble) 30H - 3FH Position data is 30H ored with data nibble F03, F02, F01, F00 of focus data. 10 Terminator and Checksum 80H - 8FH Most significant nibble is always 8.
4 30H - 38H bit0 (lsb) Auto Iris; 0 = auto, 1 = manual bit1 Camera power; 0 = off, 1 = on bit2 Lens speed; 0 = slow; 1 = fast bit3 Comm. error; 0 = no, 1 = yes bit4 - bit7 = 0011. 5 “A” Upper case “A” 6 30H - 31H bit0 (lsb) aux output; 0 = off, 1 = on 7 Terminator and Checksum 80H - 8FH Most significant nibble is always 8. Least significant (LS) nibble is the XOR of all previous bytes (LS nibble only) except for leading autobaud character F8H. 3.
Product Registration/Warranty Thank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highest quality products available with unmatched customer service levels that are second-to-none in the security industry.
