© 2009, Videolarm, Inc. All Rights Reserved QSDW and QSDP QView Series QSD Outdoor Dome www.videolarm.com Installation and Operation Instructions for the following models: CERTIFIED © 2009, Videolarm, Inc. All Rights Reserved Before attempting to connect or operate this product, please read these instructions completely.
IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read before the unit is operated. 2. Retain Instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to. 4. Follow Instructions - All operating & user instructions should be followed. 5. Electrical Connections - Only a qualified electrician should make electrical connections. 6.
TO OPEN THE HOUSING CABLE AND POWER GUIDELINES 1. Open the housing by loosening the (3) security screws This chart shows the proper current needed for power supplies for Q-View™ cameras. Use Class 2 Power only. Input voltage must be 24 VAC/VDC. CAMERAS VOLTAGE CURRENT POWER 1 24 VAC/VDC 102mA 2.5W 2 24 VAC/VDC 210mA 5W 3 24 VAC/VDC 331mA 7.9W 4 24 VAC/VDC 487mA 10.9W located on the housing ring next to the lower clear dome (Figure 1).
1. Mount the housing assembly to the mounting bracket and 3. Open the access door on the bottom of the wall mount by housing coupling. A safety cable is included with the housing to loosening the screw nearest the mounting plate (Figure 2). temporarily hold it while making wiring connections. 2. Clean the outside of the dome. Twist and Secure Conduit Entrance Figure 2 4. Attach the wires from the wall to the connector provided, using the wiring color code chart as a guide. 5.
CABLE AND POWER GUIDELINES This chart shows the proper current needed for power supplies for Q-View Series cameras. Use Class 2 Power only. Input voltage must be 24 VAC/VDC. Use the formula below to select the correct power supply for cameras connected in parallel (positive to positive, negative to negative): Total current for a 24 VAC system: CAMERAS VOLTAGE CURRENT POWER 1 24 VAC/VDC 102mA 2.5W 2 24 VAC/VDC 210mA 5W 3 24 VAC/VDC 331mA 7.9W 4 24 VAC/VDC 487mA 10.
CAMERA ADJUSTMENT CAMERA SETTINGS 1. Access the cameras by removing the dome. Loosen the locking screws on the lip of the dome. DO NOT TAKE THESE SCREWS NOTE: To determine which camera is used in your unit, locate the serial number on the inside of the housing. Match the two letter prefix with the corresponding instructions included OUT. Once the screws are loosened, turn the dome counter clockwise until it stops, then pull the dome off. here for adjustments.
HIGH-RES COLOR, FIXED LENS COMPLETION OF INSTALLATION FIXED AND FIXED VARI-FOCAL LENSES. There are no user adjustable settings on these units (Figure 14) AUTO IRIS LENSES: The auto iris can be adjusted if needed. See the Troubleshooting section for instructions. 1. When the desired focus is achieved for each camera, adjust the segmented bracket arms to the desired viewing angle. Once you've finished, put the dome back in place and check to be sure none of the cameras touch the dome.
Wiring Notes Cable Distance Wire — What to DO 250 ft 1. DO use point-to-point Unshielded Twisted Pair wire, gauge 24 or thicker, stranded or solid, Category 2, 3, 4, or 5. 300 ft 2. The video signal may co-exist in the same wire bundle as other video, telephone, data, control signals, or low-voltage power. It is also OK to run NVT video signals in or near electromagnetic fields (in accordance with National Electrical Code, local, or other local safety requirements).
NVT TROUBLESHOOTING If the voltage is greater than 1/2 volt, use an amplified receiver, such as the NV-652R, NV-862R, or NV-1662R. If you are experiencing problems, attempt to simplify your setup. Test each cable segment separately. For example, test the camera and monitor together without the other equipment. Then add in the NVT transceivers, back-to-back. Test each segment of a long cable-run independently. Attempt to isolate the problem.
TROUBLESHOOTING LINE LOCK If you experience problems with the camera picture please check these simple troubleshooting procedures for possible solutions before calling technical support. All cameras are all shipped from the factory with the line lock function disabled. If your application requires Line Lock contact Videolarm.
Mounting Template R .733 2.132 5.500 1.537 2.981 2.000 3.
Product Registration/Warranty Thank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highest quality products available with unmatched customer service levels that are second-to-none in the security industry.
