Specifications

ManualsBrandsMoog Videolarm ManualsSecurity CamerasQFDWT4-70NA

ELECTRICAL SPECIFICATIONS (OUTDOOR ON LY):

Power 24VAC, Class 2 Only

26 watts at 24 VAC (accessories)

Heater: 25 watts

Blower: .84 watts

Input Connectors (outdoor units):

BNC Connectors - 1 for each camera

Screw-down connectors - 2

NOTE: This unit is designed for operation in an

upright position. Installing the Fusionome™

upside down may cause damage to the

internal equipment, and will void the warranty.

P R ODUCT INST RUCTIONS

REVISION DATE : 02-02-2009

81-IN5247-07064 Q-View FusionDome

QF DW(T/C)X-XXXX / QIFDW(T/C)X-XXXX

CAMERAS VOLTAGE CURRENT POWER

1 24 VAC/VDC 102mA 2.5W

2 24 VAC/VDC 210mA 5W

3 24 VAC/VDC 331mA 7.9W

4 24 VAC/VDC 487mA 10.9W

Use the formula below to select the correct power supply for

cameras connected in parallel (positive to positive, negative to

negative):

Total current for a 24 V AC system:

TO TAL CURRENT = (202mA x total number of cameras)

Note: 202mA is camera plus power supply

CABLE AND P OWER GUIDELINES (Detailed in fo on P age 12)

This chart shows the proper current needed for power supplies for

Q-View™ cameras. Use Class 2 Power only. Input voltage must

be 24 VAC/VDC.

3. Pull the wires from the wall through the rectangular hole in the

wall mount bracket. Attach the wall mount to the wall using

appropriate hardware (not included).

4. Make all wiring connections (See next page). Attach the BNC

connectors to the video in.

5. Once all wiring connections are made, place the wires inside the

wall mount bracket and close the access door. Secure with the

screw removed earlier.

WALL MOUNTING THE QFD

1. A template is included as a guide for mounting the bracket to a

wall. Choose the desired location for installation and mark the

drill holes using the template. Run approximately 8"of wiring out

of the wall.

2. Open the access door on the bottom of the wall mount by

loosening the screw nearest the mounting plate (Figure 1).

Figure 1

Access door

GENERAL INST R UCTIONS:

Tools Required: .100" Flat Head Screwdriver

Phillips Head Screwdriver

Carefully remove the housing from the packaging material. Check to

be sure all parts are present.

TABLE OF CONTENTS

Ca ble and Power Guidelines 1, 11

Electrical Speciﬁcations 1

General Instructions

Wall Mounting 1

Pendant Mounting 2

Wiring 2

Camera Adjustment 2

Camera Focusin g 2

Camera Settings 3

Completion of Installation 3

NVT Instructions 4

Exploded View 6

Warranty Information 7

Se rvice and Safeguard Information 8

Troubleshooting 9

Mounting Template 12

PEN DANT MOUNTING THE QFD AND QIFD

1. This unit includes a 1 1/2" NPT housing coupling that can be used

with a standard 1 1/2" NPT pipe or with brackets designed with

1 1/2" male pipe threads, such as Videolarm's WM20G.

2. Attach the coupling to the bracket or pendant pipe (Figure 2).

NOTE: Pipe threads should be clean and rust free. Use a

sealer (such as Teﬂon™ tape or silicone sealer) on the

threads for outdoor applications

Be sure the bracket is properly and securely mounted to a

supporting structure capable of rigidly holding the weight of

the entire unit.

Figure 2

Add thread

sealing tape

Summary of content (12 pages)

PAGE 2
3. Bring all wiring through the NPT pipe or bracket. Vari-Focal Lens: First, adjust the Magnification Lock Screw to the desired magnification (telephoto to wide angle). Tighten the Lock Screw. Next, adjust the Focus Lock Screw until a clear picture is achieved. Tighten the Lock Screw (Figure 6). 4. Mount the housing assembly to the mounting bracket and housing coupling. A safety cable is included with the housing to temporarily hold it while making wiring connections.
PAGE 3
MC CAMERA DIP SWITCH SETTINGS CHART SERIAL NUMBERS BEGINNING WITH MC The operational settings for the camera are defined by ten dip switches located on the PC Board (Figure 9). Moving the switches to SWITCH the on position will activate each setting. Factory defaults are pictured below (Figure 10 and 11).
PAGE 4
COMPLETION OF INSTALLATION SERIAL NUMBERS BEGINNING WITH CB NOTE: This hi-res color camera uses a 1/4" chip and a 3-6mm 1. When the desired focus is achieved for each camera, adjust the auto iris lens. It is comparable to a 1/3" chip using a 4-9mm auto iris lens. segmented bracket arms to the desired viewing angle. Once you've finished, put the dome back in place and check to be sure none of the cameras touch the dome.
PAGE 5
Wiring Notes Cable Distance Wire — What to DO 250 ft 1. DO use point-to-point Unshielded Twisted Pair wire, gauge 24 or thicker, stranded or solid, Category 2, 3, 4, or 5. 300 ft 2. The video signal may co-exist in the same wire bundle as other video, telephone, data, control signals, or low-voltage power. It is also OK to run NVT video signals in or near electromagnetic fields (in accordance with National Electrical Code, local, or other local safety requirements).
PAGE 6
EXPLODED VIEWS OF HOUSING Wall Mount Assembly Item No. 1 2 3 4 5 n/s n/s 6 7 8 9 10 11 12 12 12 13 15 n/s n/s 16 n/s n/s n/s n/s n/s Description Wall Mount Bracket Assembly FD8 Housing Top Dome Support Ring 25W, 24VAC w/Leads FD8 Clear Dome FD8 Tinted Dome 9.25" O-ring Plastic Ring Plugs FD8 PCB FD8 Upper Housing Bracket Housing Gasket Housing Fan Adapter Bracket (In Housing Packet) 1/4 x 20 x .75" HH Bolts 1/4 Split Lock Washer 1/4 Flat Washer 10 x 32 x .
PAGE 7
IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read before the unit is operated. 2. Retain Instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to. 4. Follow Instructions - All operating & user instructions should be followed. 5. Electrical Connections - Only a qualified electrician should make electrical connections. 6.
PAGE 8
TROUBLESHOOTING If you experience problems with the camera picture please check these simple troubleshooting procedures for possible solutions before calling technical support. PICTURE IS CLEAR, LOW OR NO COLOR; PICTURE IS DARK OR GRAINY IN GOOD LIGHTING CONDITIONS The auto iris lens is set at the factory. If you experience video too light or dark you can manually adjust using the auto iris adjustment screw.
PAGE 9
NVT TROUBLESHOOTING If the voltage is greater than 1/2 volt, use an amplified receiver, such as the NV-652R, NV-862R, or NV-1662R. If you are experiencing problems, attempt to simplify your setup. Test each cable segment separately. For example, test the camera and monitor together without the other equipment. Then add in the NVT transceivers, back-to-back. Test each segment of a long cable-run independently. Attempt to isolate the problem.
PAGE 10
CABLE AND POWER GUIDELINES This chart shows the proper current needed for power supplies for Q-View Series cameras. Use Class 2 Power only. Input voltage must be 24 VAC/VDC. CAMERAS CURRENT POWER 1 VOLTAGE 24 VAC/VDC 102mA 2.5W 2 24 VAC/VDC 210mA 5W 3 24 VAC/VDC 331mA 7.9W 4 24 VAC/VDC 487mA 10.
PAGE 11
Mounting Template R .733 2.132 5.500 1.537 2.981 2.000 3.
PAGE 12
Product Registration/Warranty Thank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highest quality products available with unmatched customer service levels that are second-to-none in the security industry.