User Manual

ManualsBrandsMooer ManualsGuitar EffectsSolo - Distortion Pedal - PEDAL DISTORTER FOR ELECTRIC GUITAR

 All-sided high-gain distortion with excellent dynamic response and

definition, especially suit for solo playing

 3 Working Modes: Natural/Tight/Classic

 Full metal shell

True bypass switch

DC 9V adapter power supply

Main Features

6. Mode Switch:

Switch between Natural mode, Tight

mode and Classic mode.

7. LEVEL Knob: Adjusts the output volume.

8. TONE Knob: Adjusts the brightness of tone.

9. GAIN Knob: Adjusts the gain.

Working Mode: 3 (Natural/Tight/Classic)

Input: 1/4” monaural jack (impedance: 470k Ohms)

Output: 1/4” monaural jack (impedance: 100 Ohms)

Current Draw: 11 mA

Dimensions: 93.5mm (D) × 42mm (W) × 52mm (H)

Weight: 160g

Accessories: Owner’s Manual

* Disclaimer: Any specification’s update won't be amended in this manual.

Natural: Natural, organic distortion sound with nice dynamic response.

Tight: High gain distortion sound with powerful midrange and tight bottom end.

Classic: Vintage high gain distortion with plenty of sound details.

Distortion Pedal

1. TRUE BYPASS Footswitch:

Push down the footswitch to toggle

between on and bypass status.

2. ON/OFF LED:

Shows the on/off status of Solo,

when the LED is lit the effect is

engaged.

3. DC IN Power Jack:

For power supply, use a 9-volt

DC regulated AC adapter (plug

polarity is positive on the barrel

and negative in the center).

4. INPUT Jack:

1/4” mono audio jack, for

connecting guitar.

5. OUTPUT Jack:

1/4” mono audio jack, outputs

the signal.

PLEASE READ CAREFULLY BEFORE PROCEEDING

Power Supply

Connections

Always turn off the power of this and all other equipment before connecting or

disconnecting, this will help prevent malfunction and / or damage to other devices.

Also make sure to disconnect all connection cables and the power cord before

moving this unit.

Cleaning

Clean only with a soft, dry cloth. If necessary, slightly moisten the cloth.

Do not use abrasive cleanser, cleaning alcohol, paint thinners, wax, solvents,

cleaning fluids, or chemical-impregnated wiping cloths.

Interference with other electrical devices

Radios and televisions placed nearby may experience reception interference.

Operate this unit at a suitable distance from radios and televisions.

Location

To avoid deformation, discoloration, or other serious damage, do not expose

this unit to the following conditions:

Direct sunlight

Heat sources

Magnetic fields

Extreme temperature or humidity

Excessive dusty or dirty location

High humidity or moisture

Strong vibrations or shocks

Please connect the designated AC adapter to an AC outlet of the correct voltage.

Please be sure to use only an AC adapter which supplies 9V (±10%) DC, center

minus. The maximum working voltage shall not exceed 12V, otherwise may be

dangerous equipment damage, fire or other problems.

Unplug the AC power adapter when not using or during electrical storms.

Precautions

FCC certification

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference

that may cause undesired operation.

Power Requirements: AC adapter 9V DC (center minus plug),

recommended to use Mooer Micro Power

Very small and compact design

Summary of content (1 pages)

PAGE 1
Very small and compact design True bypass switch DC 9V adapter power supply Distortion Pedal Natural: Natural, organic distortion sound with nice dynamic response. Tight: High gain distortion sound with powerful midrange and tight bottom end. Classic: Vintage high gain distortion with plenty of sound details. 1. TRUE BYPASS Footswitch: Push down the footswitch to toggle between on and bypass status. 7 2. ON/OFF LED: Shows the on/off status of Solo, when the LED is lit the effect is engaged. 9 4 3.