Premium Dual Delay, Reverb and Looper pedal
Precautions Power Supply Please connect the designated AC adapter to an AC outlet of the correct voltage. Please be sure to use only an AC adapter which supplies 9V DC(±10%), , center negative. Unplug the AC power adapter when not in use or during electrical storms. Connections or disconnecting, this will help prevent malfunction and / or damage to other devices. Also make sure to disconnect all connection cables and the power cord before moving this unit. Cleaning Clean only with a soft, dry cloth.
Contents Panel Layout Front Panel Layout Back Panel Layout Setup Modes Play Mode Patch Mode Effect Types Reverb Delay B Delay A 01 01 02 03 04 05 07 09 09 09 10 Expression pedal 10 Looper 11 Settings Menu 13 Storing Presets 13 14 14 15 15 15 16 16 17 17 Wireless Footswitch 18 MIDI 19 Firmware Update 22 Wireless Exp.
Panel Layout Front Panel Layout Menu/Mix Control During standard operation rotate the Menu control to adjust the master mix of the ocean machine. Reverb Parameter controls Shimmer: Mix shimmer effect Decay: Length of reverb decay Tone: Reverb tonality R.Mix: Reverb wet/dry mix DelayA parameter controls FeedbackA: DelayA repeats TimeA: DelayA time ToneA: DelayA tonality D.MixA: DelayA level Delay B parameter controls FeedbackB: DelayB repeats TimeB: DelayB time ToneB: DelayB tonality D.
Back Panel Layout LEFT/MONO INPUT Left channel input Mono input LEFT/MONO OUTPUT Left channel output Mono output MIDI THRU Bypass output from midi in signal 500 EXPRESSION /EXTERNAL Input for external expression pedals or control switches 9V DC Power input (9 v DC, 500 ma, centre pin negative) RIGHT INPUT Right channel input RIGHT OUTPUT Right channel output 02 MIDI IN Input for midi signal from external devices
Setup Front of amp 03
Modes The Ocean Machine has two main operation modes to allow the device to be used in different ways. PLAY Mode - In this mode the Ocean machine operates like a tradition effects pedal and every basic effect parameter value is the same as that of it's corresponding control knob. PATCH Mode - In this mode the Ocean machine recalls saved presets and all basic effect parameter values will be the same as the recalled preset until adjusted via their corresponding control knob.
Play Mode Ocean Machine will boot directly to Play mode by default when powered on. In this mode the ocean machine will operate like a traditional stompbox. All basic effect parameters are depicted directly by the values of the physical control knobs. Reverb/DelayB/DelayA Depressing any of these footswitches once will turn on or turn off it's respective effect.
Menu Screen The menu screen allows access to deeper editing options. To access the menu screen options press the Menu control knob once. When inside the menu screen the currently selected effect block or parameter will be highlighted with a red border.
Patch Mode In patch mode the ocean machine recalls all effect settings from the stored presets and the controls work slightly differently. Reverb - Dedicated master Tap tempo.
Preset selection screen Patch 862ms Real Crystal Press the menu button whilst in patch mode on the preset selection screen to enter the Patch Control page.
Effect Types Reverb e rb F L -V D is t- Ve rb Room:Small room Reverb with a short decay Hall:Large spacious Reverb with a long decay Plate:Based on a traditional mechanical plate reverb Dist Verb:Distorted Reverb FL-Verb:Reverb with a modulated Flanger Filter:Reverb with a modulated envelope follower Reverse:Backwards Reverb Spring:Based on a vintage, large tank, spring reverb Mod:Reverb with a modulated Chorus Delay B Rea l Tri -M M od nv o d -I Digital:High fidelity delay with clean repeats Analo
Delay A Ech o R a in bow C ry s ta l Low Fuzz -B it y Digital:High fidelity delay with clean repeats Analog:Vintage BB style delay with warm degrading repeats Tape:Based on a classic reel to reel tape echo Echo:Based on a vintage echorec Liquid:Digital Delay with modulated Phaser repeats Rainbow:Special effect pitch Delay with modulation Crystal:Special effect pitch Delay with glistening highs Low-Bit:Delay with bit crusher Fuzzy:Delay with Fuzz Note: All effects marked with a have extra parameters
Looper Ocean machine comes complete with a looper with up to 44 seconds of recording time, overdubbing, independent level control and full featured half speed + reverse effects. To access the looper simultaneously depress the DelayB + DelayA footswitches.
When on the Looper screen, rotating the Menu control will adjust the playback level MIX * Note: You can go back and forth between the looper and your current operation screen while the looper is in operation by simultaneously pressing DelayB and DelayA footswitches 12
Settings Menu Inside this menu you will find various global settings Press the Setting button to enter the settings menu Press the Back button to exit the settings menu Setting Wireless Exp.
Exp. In this page we can select which parameter is controlled by an external expression pedal and adjust the minimum threshold when the expression pedal is in heel down posit Setting Expression Shimmer Decay R.Tone R.Mix R.P1 R.P2 F.Back B Time.B Tone.B D.Mix B B.P1 B.P2 F.Back A Time.A Tone.A D.Mix A A.P1 A.P2 Master Mix Min Value: 0% Rotate the Menu control to select which parameter you want the expression pedal to control.
Merge With Merge activated, trails of the delays and reverbs will blend into each other when the effect type or preset is changed Press the Menu control to switch Merge on/off Midi Mapping Ocean Machine contains a full contents table of it’s midi mapping so you don’t need to carry a manual with it for programming midi control MIDI PC# MIDI CC# MIDI PC# MIDI CC# Function CC# Valuerange Preset PC# Reverb on/off 23 0-127 1A #1 Reverb Type 3 0-8 1B #2 Shimmer 46 0-127 1C #3 Decay 47
IN & OUT On this page we can adjust the global input and output levels Patch Setting Patch Setting Reverb IN & OUT Reverb IN & OUT IN OUT 100 80 Press the Menu control to change between Input level and Output level Rotate the Menu control to adjust the level Global EQ Ocean Machine is equipped with a Global EQ section which will affect both your dry guitar signal and the sound of the effects. This can be switched on or off Setting 02 L.FREQ OFF Global EQ BASS 0dB MID 0dB OFF TREBLE H.
Reset This will perform a factory reset of your ocean machine Rotate the Menu control to select YES Press the Menu control to confirm factory reset Select NO or press the Back button to cancel the factory reset procedure Setting Setting Reset YES Reset YES NO NO Continue,press again! Storing Presets After creating a sound in Play mode or the Patch Control Page you wish to save, press the Save button.
Wireless Footswitch For a more complete experience you can purchase one of our wireless footswitch controllers to expand your Ocean Machine controls.
MIDI Ocean Machine operates on Midi Channel 1. It can receive midi signals but can not transmit them Programme Change signals (PC) are used to recall presets Control Change signals (CC) are used to switch effects on/off and control parameter values CC# Value Range Reverb On/Off 23 0-127 (On:>=64;Off:<64) Reverb type 3 0-8 Shimmer 46 0-127 Function Decay 47 0-127 Tone 48 0-127 R.Mix 49 0-127 R.P1 50 0-127 R.
Function Value Range CC# Looper In&Out 26 0-127(In:>=64;Out:<64) Rec/Dub 27 0-127 Play 28 0-127 Stop 29 0-127 Clear All 30 0-127 HalfSpeed 31 0-127(On:>=64;Off:<64) Reverse 32 0-127(On:>=64;Off:<64) Loop-Level 45 0-60 wireless 33 0-1 Expression pedal 34 0-18 Expression Min Value 35 0-100 Trail On/Off 70 0-127(On:>=64;Off:<64) EQ On/Off 36 0-127(On:>=64;Off:<64) L.FREQ 37 0-5 BASS 38 0-24 MID 39 0-24 TREBLE 40 0-24 H.
Preset Midi program NO. 1A Midi program #1 1B Midi program #2 1C Midi program #3 2A Midi program #4 2B Midi program #5 2C Midi program #6 3A Midi program #7 3B Midi program #8 3C Midi program #9 4A Midi program #10 4B Midi program #11 4C Midi program #12 Preset Midi program NO.
Firmware Update From time to time MOOER will release new firmware updates for Ocean Machine which will include new features or any bug fixes subsequent to user feedback. You will require a USB > MIDI interface cable to complete the firmware update 1.Download "OM_IAP.zip" from www.mooeraudio.com 2.Extract "OM_IAP.exe" and "OM_PROGRAM_FILE.bin" 3.Connect your midi interface to the computers USB.
