Owner’s Guide and Installation Manual 3MUR52XXD Series Fan UL Model No. : AC-552 Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER: RETAILER ADDRESS: To register your fixture, please visit our website www.montecarlofans.com 6.71 kgs 14.
Cautions and Warnings WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVETHE FOLLOWING READ AND SAVE THESE INSTRUCTIONS Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999), including fire-rated construction. Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
1 2 Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. 4 Downrod Mount Installation Loosen 2 screws on yoke to allow down rod to slip into yoke. 7 Place canopy ring over downrod then place yoke cover over downrod as shown.
10 11 12 Install keeper pin. Evenly tighten the 2 set screws on the yoke, once the down rod is in place. Make sure the studs protruding from the bottom of the Mounting bracket are installed with threads all the way through the bracket. 13 14 Safety cable installation 15 Remote transmitter dip switch Safety cable Lag screw Lag screw Safety cable Hang assembled fan from the mounting bracket installed to ceiling in previous step. Make sure the fan is hanging straight.
19 Go to step 31 to finish installation Lift Conopy allowing the 2 studs to protrude through the canopy. Next lift the cover ring and install knurled nuts as shown. Tighten the knurled nuts securely. The canopy should adjust for any irregularity in the ceiling or outlet box. 21 24 Remove side covers from canopy Remove set screws and pins from yoke as shown in inset. Remove every other screws from yoke on top of motor housing as shown. Save screws for later use.
29 27 28 Install remote receiver into the mounting bracket. Make wiring connections as indicated above. White from fan to white from remote marked N. Blue from fan to blue from remote marked light. Black from fan to Black from remote marked L. White from house to white from remote marked AC N . Black from house to Black from remote marked AC L. Connect all green ground wires to Grounded wire from House. Make wire connections to power source using wire nuts provided.
36 37 Connect white wire from fan to white wire from light fixture and then connect black wire from fan to black wire from light fixture. 39 Attach glass to light pan by locating dimples in light pan with grooves in glass and twist clockwise until tight. 42 WALL MOUNT INSTALL 38 Attach light fixture on to light pan, aligning the keyhole slots on the light fixture with the screws on light pan and twist clockwise till tight. Install the screw removed in step 35. Tighten all screws securely.
Remote Control Transmitter Features: MEDIUM SPEED LED LIGHT HIGH SPEED LOW SPEED LIGHT ON/OFF SETTING AND DIMMER (Press and hold to dim light infinitely) FA N O F F S E TT I N G (Turns fan off only) FAN SPEED Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for high. To turn fan off press square”. LIGHT DIMMER To turn light on, press light dimmer once quickly. To turn off press once quickly while light is on. To dim light hold down button “light dimmer”.
Trouble Shooting If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our Customer Service Center at the number printed on your parts list insert sheet.
Mar.2012 New format Jul.
