Owner’s Guide and Installation Manual 3ADR60XXX Series Fan CUL Model NO. : 3ADR60 Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER: RETAILER ADDRESS: To register your fixture, please visit our website www.montecarlofans.com 5.1 kgs 11.
Cautions and Warnings WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING READ AND SAVE THESE INSTRUCTIONS Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70), including fire-rated construction. Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
1 2 3 Ceiling joist Ceiling Outlet Box ON ON Ceiling Joists OFF Mounting Bracket Screw/ Washers /Spring Washers OFF 2˝ x 4˝ Outlet Box Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. Use AC 120V/60HZ power supply only.
7 8 Lead wires 9 re Yoke Downrod Keeper pin Cross pin Replace the fan housing. Align the key holes on the housing with the preinstalled set screws on top plate of fan body then turn the housing clockwise till tight. Reinstall the set screw removed in installation step 5 and tighten all screws securely. Partially loosen downrod set screws from yoke at top of motor assembly. Remove preassembled cross pin and keeper pin from downrod. Keep parts.
13 14 15 Mounting bracket Keeper pin Attach Safety Cable to Ceiling Support Cable Cross pin Tab Tab Safety cable from fan Slot Set screw Hanger ball Cable clamp Slip downrod into motor yoke, aligning holes and install cross pin and keeper pin. Insert cross pin through yoke and downrod until point appears on the other side, and insert keeper pin on cross pin. Pull the downrod up tight against the cross pin, and then evenly tighten the downrod set screws on motor housing yoke.
17 Partially loosen one and remove one preassembled screw from mounting bracket. Save screw. © 2017 Monte Carlo Fan Company 18 19 Lift canopy up, aligning its keyhole slot with the preassembled screw on mounting bracket and twist clockwise to lock in place. Reinstall the screw removed in step 17 and tighten all screws securely. Do not over tighten it. 6 Attach canopy bottom cap onto canopy by aligning its notch with the screws on mounting bracket and twist clockwise till tight.
REMOTE CONTROL SETTING and OPERATION Remove the battery cover from the remote control transmitter and install battery. Replace the cover. Note: Use 2 1.5V/AAA battery to replace battery. (Fig. 1) Note: If not using for long periods of time, remove battery to prevent damage to remote transmitter, and store the remote transmitter away from excess heat or humidity. Install Transmitter wall mount cradle with 2 screws provided.
The buttons on the remote control transmitter control the fan speed and light as follows. (Fig. 4) LED Indicator UP Speed Press the button to get desired fan speed, Low to High. Press the button to get desired fan speed, High to Low. Down Speed Press the OFF button to turn fan off. Turn Fan Off Press this forward/reverse button to get desired airflow direction. Fan must be running to reverse. It will take about 25 seconds for fan to slow down and change rotation direction.
Trouble Shooting or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, installation, please call our Customer Service Center at the number printed on your parts list insert sheet. Warning means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. Trouble 1. If fan does not start: Suggested Remedy 1.
Nov.
