Operating instructions

ManualsBrandsMonster ManualsHousehold AppliancesSC60

Operating Instruction

Switching On

Insert the plug into the mains wall socket and switch

it on..

The power on light should illuminate, the appliance

will produce steam and the tank will become pressu

rised. Heating time is approximately 5 minutes with

cold water. Filling boiler with hot water will shorten

heat up time.

The heater is repeatedly switched on during opera

tion, in order to maintain constant steam pressure.

NOTE: Do not switch the steam cleaner on if there

is no water in the boiler.

CAUTION: Read the instructions for “Filling your

Steam Cleaner With Water” (below) before opening

the Safety Filler Cap.

CAUTION: Always unplug before ﬁlling.

IMPORTANT: Do not add cleaning solutions, scented

perfumes, oils or any other chemicals to the water

used in this appliance. Use only tap water or if the

tap water in your area is very hard use distilled/pu

riﬁed water.

Filling Your Steam Cleaner With Water

Step 1: Before ﬁlling the steam cleaner, remove the

plug from the mains wall socket.

Step 2: Turn Safety/Filler Cap counter clockwise

until removed.

Step 3: Using the ﬁller funnel add 1.2L (2 pints) of

water. Do not overﬁll. Replace Safety/Filler Cap by

turning clockwise.

Step 4: Plug the unit into a standard 220volt wall

socket .

Step 5: Allow approximately 5 minutes for steam to

reach its working temperature and pressure..

Step 6: Connect desired attachments onto the

Flexible Steam Hose.

CAUTION: Always drain condensate from hose

before use or if unit has been left idle for a period

of time. To drain hose, direct nozzle into an appro

priate container or sink and switch on the steam.

When hose has been drained, normal use may

be resumed. Never direct nozzle towards people,

animals or plants.

Regulating the volume of steam

The amount of steam can be regulated according to

requirement by sliding the steam control on top of the

steam gun. Forwards to increase steam, backwards

to reduce steam.

IMPORTANT: When the Monster 60 SuperClean has

run out of water, steam output will cease.

CAUTION: Allow unit to cool for 5 minutes before

reﬁlling. If reﬁlling the machine while still hot, the ﬁrst

drops of water may bubble up.

Extreme care should be taken when opening the

Safety/Filler Cap as cap may become hot during use

and escaping steam can cause scalding.

Reﬁlling the boiler

Step 1: remove the 3-pin plug from the wall soc

ket.

Step 2: Cover the safety ﬁller cap with a towel or cloth

and carefully loosen it by turning counter clockwise. If

the tank has not been completely vented any residual

steam will be released below the safety/ﬁller cap.

When the hissing stops and the last of the steam

has been released, remove the ﬁller cap.

Step 3: Allow the steam cleaner to cool for 5 minutes

before re-ﬁlling with water. If the steam cleaner is still

hot, there is a risk that water will be squirted back

during ﬁlling and cause scalding.

Step 4: Reﬁll water tank with a maximum of 1.2L (2

pints) of water using the ﬁller funnel.

Only use the ﬁller funnel supplied. Its nozzle is

made from a heat resistant material to prevent it

from melting when ﬁlling a hot boiler. Other plastic

items can melt and become welded to the inside of

the boiler spout voiding your warranty.

Step 5: Firmly screw the safety ﬁller cap back onto

the unit by turning clockwise.

Step 6: Connect the 3-pin plug to the wall socket.

Switching the cleaner OFF

Remove the 3-pin plug from the wall socket.

Any remaining water can be left in the cleaner.