® Home Theatre Reference HTFS500 POWERCENTER HTFS1000 POWERCENTER ™ ™ Owner’s Manual
TABLE OF CONTENTS Page Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Proper Grounding and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii A Note from The Head Monster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INFORMATION Please read and observe the following safety points at all times. WARNING – Power Sources Do not plug this PowerCenter™ into a power outlet that differs from the source indicated for safe use on the PowerCenter.™ If you don’t know the type of electrical power that is supplied to your home, consult your local power company or a qualified electrician. WARNING – Grounding and Polarization A.
WARNING – Power Cord Safety A. When routing your PowerCenter’s AC power cord, do not place it near heavy foot traffic areas (e.g., hallways, doorways, and floors). Do not create a trip hazard with the power cord. B. If your power cord’s protective jacket begins to rip or fray, exposing the internal wiring, shielding, etc., disconnect it from the power source and discontinue use of the Monster PowerCenter™ immediately. See the Warranty Information section of this owner’s manual for important details.
PROPER GROUNDING AND INSTALLATION WARNING – Proper Grounding Monster PowerCenters™ require a properly grounded 3-wire outlet for safety and to protect connected equipment. If you’re not sure if your home’s electrical wiring is properly grounded, have it checked by a qualified electrician. Many older buildings are inadequately wired. It’s very common for a building to be improperly grounded.
A NOTE FROM THE HEAD MONSTER Dear Enthusiast, THANK YOU for purchasing the Monster Power Home Theatre Reference PowerCenter™ for flat screen, plasma, and LCD televisions. This PowerCenter reflects our commitment to creating performance-enhancing solutions for home theatre systems, so you can enjoy superior sound and picture quality. As a long-time audiophile and serious home theater enthusiast, I always knew problematic AC power could degrade picture and sound quality.
Other Monster Power breakthroughs include patented Tri-Mode™ protection (HTFS1000 only) and patented Dual Mode Plus™ protection (HTFS500 only), both featuring an audible alarm. This feature automatically disconnects power from your electronics if you’re hit by a big surge. The PowerCenter is also small in design to easily fit behind your flat screen, plasma, or LCD TV. These days, home theater components are better than ever, providing thrilling and dramatic sound and razor sharp picture.
MONSTER’S PATENTED CLEAN POWER™ Monster’s High Definition Video (HDV) Clean Power circuitry is engineered specifically to help eliminate noise such as electromagnetic interference (EMI) and radio frequency interference (RFI) from high definition video sources. Clean Power incorporates sophisticated filters to dramatically reduce this electronic noise on your AC power line to give you the best possible sound and picture from your high definition displays, including plasma, LCD or HDTVs.
THE MINDS BEHIND THE MONSTER POWERCENTER DESIGN Richard Marsh – There are few experts able to solve the complex problems associated with AC power and complex home theater systems. Richard Marsh is one of these illustrious few. He has designed best selling power conditioning components costing more than $3,000 US and now brings his expertise to Monster Power. Richard developed Monster’s patented Clean Power ™ circuitry. He is also responsible for several other ground-breaking designs.
Noel Lee – Noel Lee, The Head Monster, is best known for popularizing the concept of high performance audio cable 25 years ago with his creation of Monster Cable. Originally a laserfusion design engineer at Lawrence Livermore National Laboratory and later a touring musician, Noel has invented or co-invented over 250 U.S. and international patents and drives the explosive growth of The Monster Group companies in more than 80 countries worldwide.
MONSTER HTFS500 POWERCENTER FEATURES HTFS500 SIDE VIEW HTFS500 TOP VIEW HTFS500 SIDE VIEW 12 (4&3 10 !# $# ). ^ 6 M! -). ()'( $%&).)4)/. 6)$%/ 0/7%2#%.4%2 4- WITH #LEAN 0OWER 4- ($6 &ILTERING 2%3%4 2 12 /&& 02/4%#4)/. /. '2/5.
MONSTER HTFS1000 POWERCENTER FEATURES HTFS1000 TOP VIEW HTFS1000 SIDE VIEW 9 ).054 6/,4!'% 6 4 5 6 7 8 '2/5.$ /+ 02/4%#4)/. /. 7)2).' 2%6%23%$ #,%!. 0/7%2 /. 37)4#(%$ /. 3 1 6/,4!'% !-0%2!'% /. /&& HTFS1000 SIDE VIEW #522%.4 53!'% ! (4&3 !# $# ). ^ 6 M! -). ()'( $%&).)4)/. 6)$%/ 0/7%2#%.4%2 4- WITH #LEAN 0OWER 4- ($6 &ILTERING 10 11 12 '2/5.$ /+ 02/4%#4)/. /. 7)2).' 2%6%23%$ #,%!. 0/7%2 /. 13 37)4#(%$ /. 6/,4!'% !-0%2!'% ).
MONSTER HTFS500 / HTFS1000 POWERCENTER FEATURES 1. “On/Off Button“ (HTFS1000 only): Press to turn on/off the switched outlet (labeled as HDTV). Note: The ON/OFF button has no effects on the unswitched outlet (labeled as ACCESSORY), which remains on as long as the HTFS1000 is plugged into an active AC outlet. 2. “Reset/Off“ Switch (HTFS500 only): Switch to turn on/off both AC outlets on the HTFS500. Note 1: This RESET/OFF switch is also a circuit breaker.
10. Remote “AC/DC In” Control: Allows you to automatically turn on/off the PowerCenter’s switched outlet(s) via the Remote “AC/DC Out” on another component (such as an A/V receiver or custom installation equipment). Note 1: To use this feature, the ON/OFF button on HTFS1000 or the RESET/OFF switch on HTFS500 should be set to OFF. Note 2: The voltage range of the external source’s output for remote control should be 3~30V (AC or DC). 11.
INSTALLATION OF MONSTER HTFS 500 POWERCENTER™ WALL-MOUNT BRACKETS HTFS 500 Mounting Instructions ! Step 1. Determine where you will mount your HTFS PowerCenter.™ Fit bracket A to a side-flap, holding it to the wall and marking the holes. Step 2. Fasten Bracket A to the wall with standard 1” self-tapping drywall screws (Hardware not included). " Step 3. Insert one of the side-flaps of the HTFS PowerCenter into bracket A. Step 4.
INSTALLATION OF MONSTER HTFS 1000 POWERCENTER™ WALL-MOUNT BRACKETS HTFS 1000 Mounting Instructions ! Step 1. Determine where you will mount your HTFS PowerCenter.™ Fit bracket A to a side-flap, holding it to the wall and marking the holes. Step 2. Fasten Bracket A to the wall with standard 1” self-tapping drywall screws (Hardware not included). " Step 3. Insert one of the side-flaps of the HTFS PowerCenter into bracket A. Step 4.
HOOK-UP GUIDE High Definition Video (HDV) Outlet Hook-Up These outlets have a special filter circuit that is optimized to reduce interference to your high definition video components. A) HDTV: Plug your high definition video monitor (such as a plasma HDTV) into the outlet labeled as HDTV. Note: The HDTV outlet on the HTFS1000 and HTFS500 is switched. B) ACCESSORY: Plug an additional component (such as a HDTV receiver, a satellite receiver, a DVD player, etc.) into the outlet labeled as accessory.
HOOK-UP GUIDE Display Unit Hook-Up (HTFS1000 only) The display unit of HTFS1000 is detachable from the main unit. The display unit is connected to the main unit via a 4-wire RJ11 phone cable. Connect one end of the supplied phone-type cable to the corresponding jack on the detachable display unit. Connect the other end of the cable to the jack on the main unit of the HTFS1000. Note: The cable included is 6 feet in length.
HOOK-UP GUIDE Remote “AC/DC In” Control Hook-Up This feature connects your PowerCenter to an automated Home Theater control system or allows another component with a Remote “DC Out” connection to automatically turn on and off your PowerCenter. A) Plug the AC power cable of the component you are using to control the PowerCenter into an unswitched outlet on the PowerCenter. Note: This component must deliver a control voltage between 3-30 volts DC.
TROUBLESHOOTING Symptom Possible Cause Remedy The PowerCenter is not receiving power. The PowerCenter is not turned on. • Turn the PowerCenter switch on. • Make sure the PowerCenter’s AC power plug is plugged into a properly grounded 120 volts (nominal) wall outlet. • In some households, a wall switch may need to be thrown to make the wall plug come alive. Try turning on the light switches located near the wall unit powering the PowerCenter.
TROUBLESHOOTING 16 Symptom Possible Cause Remedy The PowerCenter is not receiving power (continued). The component is plugged into a switched outlet and the PowerCenter has not been turned on. • Turn the PowerCenter on. The PowerCenter is plugged into a Switched outlet, but power on the component is not On. In some instances, a component plugged into a switched outlet won’t receive power when the PowerCenter is turned On unless the component power is also switched On.
TROUBLESHOOTING Symptom Possible Cause Remedy Speakers emit a humming or buzzing noise. The PowerCenter is sharing AC power with equipment that is not properly grounded. • Connect your PowerCenter to a dedicated outlet. • Try unplugging different components from the PowerCenter one at a time to see if the noise stops. If a component is discovered to be improperly grounded, attach a copper wire from the component’s chassis to the PowerCenter’s grounding post. The display unit is not functioning.
SPECIFICATIONS HTFS500 POWERCENTER ™ Continuous Duty Electrical Rating 120V/60Hz Maximum Current Rating 15A/1800W Protection Modes Line-Neutral (L-N) Line-Ground (L-G) Neutral-Ground (N-G) Total Energy Dissipation Clamping Level (TVSS Voltage) Clamping Response Time Remote Trigger In Dimensions 18 2775 Joules 330 Volts Less than 1 Nanosecond (<1Ns) 3 – 30v DC, 10mA MIN Width: 3.56 inches 90.424mm Height: 1.4 inches 35.56mm Length: 7.5 inches 190.
SPECIFICATIONS HTFS1000 POWERCENTER ™ Continuous Duty Electrical Rating 120V/60Hz Maximum Current Rating 15A/1800W Protection Modes Line-Neutral (L-N) Line-Ground (L-G) Neutral-Ground (N-G) Total Energy Dissipation Clamping Level (TVSS Voltage) Clamping Response Time Remote Trigger In Dimensions 3145 Joules 330 Volts Less than 1 Nanosecond (<1Ns) 3 – 30v DC Width with Display Unit: 5.375 inches Width without Display Unit: 3.56 inches Height with Display Unit: 1.
Monster, LLC 7251 West Lake Mead Blvd. • Las Vegas, NV 89128 • USA Monster Technology International Limited Ballymaley Business Park • Gort Road • Ennis, Co. Clare • Ireland Visit us on the web at: MonsterPower.com Call us toll-free in the U. S. at 877-800-8989 or toll-free in Canada at 001-866-348-4171. The Monster Power Home Theatre Reference PowerCenter HTFS 500 and PowerCenter HTFS 1000 are protected under U.S. Pat. No. 5,589,718; 6,683,770; 6,614,636; 6,473,510; 6,456,091; D 446,504.
® De référence pour cinéma maison HTFS500 POWERCENTER HTFS1000 POWERCENTER ™ ™ Guide de l’Utilisateur rm 162686
TABLE DES MATIÈRES Page Informations importantes sur la sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Mise à la terre et l’installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Message de Head Monster. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INFORMATIONS IMPORTANTES SUR LA SÉCURITÉ Veuillez lire et respecter les consignes de sécurité suivantes en toute circonstance. MISE EN GARDE – Sources d’alimentation Ne pas brancher ce PowerCenter™ dans une autre prise de courant que la source indiquée comme étant sécuritaire sur le PowerCenter™. Veuillez consulter l’entreprise de distribution électrique de votre région ou un électricien qualifié si vous ignorez le type d’alimentation électrique de votre domicile.
MISE EN GARDE – Liquides : pour éviter tout risque d’électrocution A. Ne pas faire fonctionner le Monster PowerCenter™ en cas de déversement de liquide sur ou dans le dispositif. B. Ne pas faire fonctionner le Monster PowerCenter™ s’il pleut à côté, en cas de déversement d’eau ou dans des lieux humides (par ex., baignoire, cuisine ou évier). MISE EN GARDE – Mesures de sécurité concernant le cordon d’alimentation A. Ne pas placer le cordon d’alimentation c.a.
MISE À LA TERRE ET INSTALLATION APPROPRIÉES WARNING – Mise à la terre correcte Le PowerCenters™ Monster nécessite une prise de courant trifilaire correctement mise à la terre pour des questions de sécurité et pour protéger les appareils branchés. En cas de doute sur le câblage électrique de votre domicile, le faire vérifier par un électricien qualifié. Il est fréquent que le câblage des logements plus anciens soit inadéquat. Généralement, ils n’offrent pas une mise à la terre adéquate.
MESSAGE DE HEAD MONSTER Cher passionné, Nous vous REMERCIONS d’avoir fait l’acquisition du Power Home Theatre Reference PowerCenter™ Monster pour téléviseurs à écran plat, à plasma et à ACL. Ce PowerCenter reflète notre engagement à créer des solutions qui améliorent la performance des systèmes de cinéma maison afin que vous puissiez bénéficier d’une restitution de son et d’image supérieure.
fréquences radio et interférences électromagnétiques générées sur la ligne d’alimentation et provenant du branchement d’autres appareils. En conséquence, vous obtiendrez une image de la meilleure définition possible et dont la performance n’est pas affectée par le bruit vidéo. La protection brevetée Tri-Mode™ (HFTS 1000 uniquement) et la protection brevetée Dual Mode Plus™ (HTFS 500 uniquement), dotées toutes deux d’une alarme sonore, comptent parmi les autres innovations de pointe de Monster Power.
CLEAN POWER™ BREVETÉ DE MONSTER La Circuiterie Vidéo Haute Définition (HDV) Clean Power Monster est spécialement conçue pour éliminer le bruit, Notamment les Interférences Electromagnétiques (EMI) et de radiofréquences (RFI) des sources vidéo haute définition.
LES CERVEAUX À L’ORIGINE DU CONCEPT DU POWERCENTER MONSTER Richard Marsh – Il n’y a que peu d’experts capables de résoudre les problèmes complexes liés à l’alimentation c.a. et aux systèmes de cinéma maison. Richard Marsh compte parmi ces rares experts. Il a conçu les meilleurs composants de conditionnement d’alimentation valant plus de 3 000 $ US et il met maintenant son expertise au service de Monster Power. Richard a développé les circuits du Clean Power™ breveté de Monster.
Noel Lee – Noel Lee, le Head Monster, est essentiellement connu pour avoir popularisé le concept de câbles audio de haut rendement il y a 25 ans avec le création de Monster Cable.
CARACTÉRISTIQUES DU POWERCENTER HTFS 500 MONSTER HTFS500 VUE LATÉRALE HTFS500 VUE DE HAUT HTFS500 VUE LATÉRALE 12 (4&3 10 !# $# ). ^ 6 M! -). ()'( $%&).)4)/. 6)$%/ 0/7%2#%.4%2 4- WITH #LEAN 0OWER 4- ($6 &ILTERING 2%3%4 2 12 /&& 02/4%#4)/. /. '2/5.
CARACTÉRISTIQUES DU POWER CENTER HTFS 1000 MONSTER HTFS1000 VUE DE HAUT HTFS1000 VUE LATÉRALE 9 ).054 6/,4!'% 6 4 5 6 7 8 '2/5.$ /+ 02/4%#4)/. /. 7)2).' 2%6%23%$ #,%!. 0/7%2 /. 37)4#(%$ /. 3 1 6/,4!'% !-0%2!'% /. /&& HTFS1000 VUE LATÉRALE #522%.4 53!'% ! (4&3 !# $# ). ^ 6 M! -). ()'( $%&).)4)/. 6)$%/ 0/7%2#%.4%2 4- WITH #LEAN 0OWER 4- ($6 &ILTERING 10 11 12 '2/5.$ /+ 02/4%#4)/. /. 7)2).' 2%6%23%$ #,%!. 0/7%2 /. 13 37)4#(%$ /. 6/,4!'% !-0%2!'% ).
CARACTÉRISTIQUES DU POWERCENTER HTFS 500/ HTFS 1000 MONSTER 1. Touche « On/Off » (marche/arrêt) (HTFS 1000 uniquement) : Appuyer dessus pour mettre en marche/arrêter la sortie commutée (avec l’indication HDTV). Remarque : La touche « ON/OFF » (marche/arrêt) n’a aucune action sur la sortie non commutée (avec l’indication « ACCESSORY » (accessoire), qui reste en position de marche aussi longtemps que le HTFS 1000 est branché dans une sortie c.a. active. 2.
8. Voyant « Switched On » (position de marche) (HTFS 1000 uniquement) : Indique la mise sous tension du composant branché dans la sortie commutée (avec l’indication « HDTV ») une fois la touche « ON/OFF » (marche/arrêt) enfoncée. 9. Tension d’entrée (V) / Consommation de courant (A) Affichage numérique (HTFS 1000 uniquement) : Avec la touche « VOLTAGE/AMPERAGE » (tension/ampérage), indique la tension d’entrée (en volts, V) ou la consommation de courant (en ampères, A) du système. 10.
INSTALLATION DES SUPPORTS DE MONTAGE MURAL DU HTFS 500 DE MONSTER POWERCENTER™ Instructions de montage du HTFS 500 ! Étape 1. Déterminez l’endroit où vous désirez monter votre HTFS PowerCenter.™ Adaptez le support A au volet latéral, en le maintenant sur le mur pour marquer les trous. Étape 2. Fixez le support A au mur à l’aide de vis autotaraudeuses standard pour cloison sèche de 1 po (quincaillerie non comprise). " 10 Étape 3. Insérez l’un des volets latéraux du HTFS PowerCenter dans le support A.
INSTALLATION DES SUPPORTS DE MONTAGE MURAL DU HTFS 1000 DE MONSTER POWERCENTER™ Instructions de montage du HTFS 1000 ! Étape 1. Déterminez l’endroit où vous désirez monter votre HTFS PowerCenter.™ Adaptez le support A au volet latéral, en le maintenant sur le mur pour marquer les trous. Étape 2. Fixez le support A au mur à l’aide de vis autotaraudeuses standard pour cloison sèche de 1 po (quincaillerie non comprise). " Étape 3. Insérez l’un des volets latéraux du HTFS PowerCenter dans le support A.
GUIDE DE BRANCHEMENT Branchement de la prise vidéo haute définition (HDV) Ces prises sont dotées d’un circuit de filtrage spécial optimisé pour réduire l’interférence de vos composants vidéo haute définition. A) TVHD : Brancher le moniteur vidéo haute définition (type TVHD à plasma) dans la sortie avec l’indication HDTV. Remarque : La sortie « HDTV » du HTFS 1000 et du HTFS 500 est commutée.
GUIDE DE BRANCHEMENT Branchement du dispositif de visualisation (HTFS 1000 uniquement) Le dispositif de visualisation du HTFS 1000 peut être retiré de l’unité principale. Le dispositif de visualisation est relié à l’unité principale par un câble téléphonique RJ11 à 4 fils. Brancher l’une des extrémités du câble téléphonique fourni dans la prise correspondante du dispositif de visualisation amovible. Brancher l’autre extrémité du câble dans la prise de l’unité centrale du HTFS 1000.
GUIDE DE BRANCHEMENT Branchement de la télécommande « AC/DC In » (entrée c.a./c.c.) : Cette fonctionnalité connecte le PowerCenter sur un système automatisé de cinéma maison ou permet à un appareil muni d’une connexion « DC Out » (sortie c.c.) télécommandée d’activer automatiquement la mise en marche et l’arrêt du PowerCenter. A) Brancher le câble d’alimentation c.a. de l’appareil utilisé pour commander le PowerCenter à distance dans une prise non commutée du PowerCenter.
DÉPANNAGE Symptôme Cause possible Solution Le PowerCenter n’est pas sous tension. Le PowerCenter n’est pas allumé. • Mettre le commutateur du PowerCenter en position de marche. • S’assurer que la prise c.a. du PowerCenter est branchée dans une prise murale de 120 V correctement mise à la terre. • Dans certains cas, il peut être nécessaire de basculer un interrupteur mural en position de marche pour que la prise soit alimentée.
DÉPANNAGE Symptom Cause possible Solution Le PowerCenter n’est pas sous tension. Trop d’appareils ont été branchés, ce qui a provoqué une surcharge et déclenché le disjoncteur thermique. Veuillez prendre note : La consommation totale de courant de tous les composants alimentés par le PowerCenter ne doit pas excéder 1800 watts. • Appuyer sur le bouton du disjoncteur thermique du PowerCenter (avec l’indication « RESET » (réinitialisation) sous le cordon d’alimentation) sur « Reset ».
DÉPANNAGE Symptôme Cause possible Solution Les haut-parleurs émettent un ronflement. Le PowerCenter partage le courant c.a. avec un appareil qui n’est pas correctement mis à la terre. • Brancher le PowerCenter dans une prise dédiée. Le dispositif de visualisation ne fonctionne pas. Il n’y a pas de connexion sécurisée entre le dispositif de visualisation et l’unité principale.
SPÉCIFICATIONS HTFS500 POWERCENTER ™ Tension nominale en service continu 120 V/60 Hz Courant nominal maximum 15 A/1800 W Modes de protection Ligne-Neutre (L-N) Ligne-Mise à la terre (L-G) Neutre-Mise à la terre (N-G) Dissipation d’énergie totale Niveau de blocage (Tension TVSS ) Temps de réponse de blocage Déclencheur d’entrée à distance Dimensions 18 2775 joules 330 volts Moins de 1 nanoseconde (<1Ns) 3 à 30 V c.c.
SPÉCIFICATIONS HTFS1000 POWERCENTER ™ Tension nominale en service continu 120 V/60 Hz Courant nominal maximum 15 A/1800 W Modes de protection Ligne-Neutre (L-N) Ligne-Mise à la terre (L-G) Neutre-Mise à la terre (N-G) Dissipation d’énergie totale Niveau de blocage (Tension TVSS ) Temps de réponse de blocage Déclencheur d’entrée à distance Dimensions 3145 joules 330 volts Moins de 1 nanoseconde (<1Ns) 3 à 30 V c.c.
Monster, LLC 7251 West Lake Mead Blvd. • Las Vegas, NV 89128 • USA Monster Technology International Limited Ballymaley Business Park • Gort Road • Ennis, Co. Clare • Ireland Visitez notre site Web : MonsterPower.com Call us toll-free in the U. S. at 877-800-8989 Appelez-nous sans frais au : 001-866-348-4171. Le Monster Power Home Theatre Reference PowerCenter HTFS 500 et PowerCenter HTFS 1000 sont protégés par les brevets U.S. Nº. 5,589,718 ; 6,683,770 ; 6,614,636 ; 6,473,510 ; 6,456,091 ; D 446,504.