Ma User Manual Wireless HD AV Transmitter & Receiver Kit REV.1.
Thank you for purchasing this Wireless HD AV Transmitter & Receiver Kit. Please read the following instructions carefully for your safety and prevention of property damage. Do not use the product in the extreme hot, cold, dusty or humid environments. Prevent friction with hard objects, or it may lead to surface abrasion, components falloff or hardware damage. Avoid the product falling down from a high place, or it may damage the hardware.
1. Introduction Wireless HD AV Transmitter & Receiver Kits run at 5GHz operation frequency to deliver uncompressed HD video/audio 20 meters open field and 10 meters through wall with hidden antenna. This device kits make wireless connection by using WHDI Technology from HD Media Source Devices such as HD Disc Player, PC, Game Console, Settop Box to Display Device for example LCD, Plasma or LED TV, Projector… while keep wire-equivalent quality and no latency. 2.
3. General Specifications Video Format Support TV: 1080p, 1080i, 720p, 576p, 480p PC: VGA(640x480), SVGA(800x600), XGA(1024x768), SXGA(1280x1024) Audio Format Support PCM, DTS, DOLBY DIGITAL RF Communication System MIMO Modulation OFDM Maximum Transmission Power 12dBm Image Transmission Distance 20 meters open field and 10 meters through wall Image Delay < 1ms Antenna High Performance Internal Antennas Operating Frequency 5.1GHz to 5.
4.Package contents Standard Package Wireless HD AV Transmitter, Tx x1 Wireless HD AV Receiver, Rx DC 5V Power Adapter for Tx and Rx x1 x2 HDMI Extension Cable, 1.2M x1 Infrared Eye Extension Cable, 1.5M x1 User Manual x1 Full Package with HDMI Switch and IR Extender Box Wireless HD AV Transmitter, Tx x1 Wireless HD AV Receiver, Rx x1 DC 5V Power Adapter for Tx and Rx x2 HDMI Extension Cable, 1.
5. Product Overview 5.1 Wireless HD AV Transmitter Unit Image 1 1. IR: Connect with IR Out port (9 in Image 3) of the HDMI Switch. Note: If you are not using enclosed HDMI Switch, you can only connect one HD Media Device with the Transmitter unit: Please connect the IR port with enclosed Infrared Eye Cable and place the IR flasher close to the IR sensor of the Media Device. Then you can control the Media Device by using its remote control at the Wireless Receiver side. 2.
3. DC IN: Connect with DC Power port (11 in Image 3) of the HDMI Switch. Note: If you are not using enclosed HDMI Switch, please connect this port with enclosed power supply (DC 5V Power Adapter). 1 . ON/OFF Switch: Power on/off the Wireless Transmitter unit. 2 . Wireless Link Indicator: Indicate that the wireless connection is linked up. 3 . Video Signal Indicator: Indicate that the video signal connection is linked up. 4 Power Indicator: Indicate when the Wireless Transmitter Unit is powered on.
1 HDMI OUT: Connect with a Display Device (e.g. LCD, Plasma or LED TV) via HDMI cable. Note: The display device should have an HDMI IN port. 2 DC IN: Connect with the power supply (enclosed DC 5V Power Adapter). 3 ON/OFF Switch: Power on/off the Wireless Receiver unit. 4 Video Signal Indicator: Indicate that the video signal connection is linked up. 5 Wireless Link Indicator: Indicate that the wireless connection is linked up. 6 Power Indicator: Indicate when the Wireless Receiver Unit is powered on.
1. HDMI IN 1: Connect with HD Media Device via HDMI Cable. 2. HDMI IN 2: Connect with HD Media Device via HDMI Cable. 3. HDMI IN 3: Connect with HD Media Device via HDMI Cable. 4. HDMI IN 4: Connect with HD Media Device via HDMI Cable. 5. HDMI OUT A: Connect with Display Device directly via an HDMI Cable. It can output any Media Source from the HD Media Devices connected with the 4 HDMI IN ports of the switch. 6. ON/OFF Switch: Power on/off the HDMI Switch. 7.
5.3.2 Remote Control Image 4 1. A-1 Select HDMI IN 1 device. Connect HDMI IN 1 to HDMI OUT A Channel. 2. A-2 Select HDMI IN 2 device. Connect HDMI IN 2 to HDMI OUT A Channel. 3. A-3 Select HDMI IN 3 device. Connect HDMI IN 3 to HDMI OUT A Channel. 4. A-4 Select HDMI IN 4 device. Connect HDMI IN 4 to HDMI OUT A Channel. 5. B-1 Select HDMI IN 1 device. Connect HDMI IN 1 to HDMI OUT B Channel. 6. B-2 Select HDMI IN 2 device. Connect HDMI IN 2 to HDMI OUT B Channel. 7. B-3 Select HDMI IN 3 device.
IR Extender Box Note: You only need to use the IR Extender Box when you use the Transmitter unit with the HDMI Switch. Image 5 1-4 IR: Connect up to 4 HD media devices with enclosed IR extension cables. Place the IR flasher on the extension cables close to the IR receivers of the media devices. 5 DC IN: Connect with the power supply (enclosed DC 5V Power Adapter). 6 Link Indicator: Indicate IR signal connection. 7 Power Indicator: Indicate when the extension box is powered on.
6. Installation Diagram 6.1 Full Package with HDMI Switch and IR Extender Box Image 6 Installation Diagram for Matrix Display How to install the Transmitter unit: You can connect up to 4 HD media devices with the Wireless Transmitter unit via the HDMI Switch. Plug the HDMI Switch to the Transmitter unit and place them near your HD media devices. Connect your HD media devices with the HDMI Switch via HDMI Cables. Connect IR Extender Box with your HD media devices via enclosed IR Extension Cables.
How to install the Receiver unit: Place the Receiver unit near your display device (Display B). Connect the HDMI cable to the ‘HD OUT’ port of the Receiver unit. Connect the other side of the HDMI cable to the HDMI connection of your display device (Display B). Now connect the power supply of both the Transmitter and Receiver unit to a wall outlet and to the ‘DC IN’ connection of the Transmitter and Receiver unit.
6.2 Standard Package Image 7 Installation Diagram for Single Display How to install the Transmitter unit: Place the Transmitter unit near your HD media device. Connect the Infrared Eye Extension Cable to the ‘IR’ port on the Transmitter unit. Place the IR flasher near the IR receiver of the HD media devices. Connect the HDMI cable to the ‘HD IN’ connection of the Transmitter unit. Connect the other side of the HDMI cable to your HD media device.
7. Using Wireless HD AV Kit The Wireless HD Transmitter & Receiver Kit has now been setup. You can enjoy the full potential of wireless Full HD streaming! Make sure all devices have been started. Bear in mind that starting the Transmitter & Receiver Kit can take up to 12 minutes. Use enclosed remote control to select the video source from HD IN 1 to HD IN 4 to display on Display A. You can also use the remote control to select the video source for showing on Display B.
All information on this manual is subject to change without notice due to technical reasons. Please contact our hotline for after sales support.
