3-Port COMBO FREE DVI KVM SWITCH ( with Audio ) User’s Manual Revision 2.
1. Introduction Thank you for your purchase of Combo Free DVI KVM Switch! You now have a high quality, durable system that will enable you to control 3 Host computers and/or servers by using PS/2 and/or USB Connectors from one console (PS/2 & USB Mouse, PS/2 & USB Keyboard, and Monitor). 1.1 Features 1. Console your Keyboard/Mouse via either way of PS/2 and/or USB arbitrarily. 2. Controls 3 DVI computers from a single console (Keyboard/Mouse) over USB and/or PS/2 connections. 3. Speaker enabled. 4.
2. Specifications 2.
3. System Requirements Console DVI monitor capable of the highest resolution. PS/2 and/or USB Keyboard/Mouse Computer or Server The following equipment must be equipped with each computer or server. - Type A USB port. - DVI connector. Cables The Combo Free DVI KVM Switch is using separate (DVI + USB/Audio) cables. To purchase the specific cable sets, please contact your dealer. 4. Single installation 4.1 Precaution: 1.
. Operations The 3-Port Combo Free DVI KVM Switch has the ability to switch the keyboard, video, mouse simultaneously Note: When using the two-step Hot Key sequences, the keys must be pressed within 5 seconds; otherwise the Hot Key action will be terminated. 5.1 Push Button on front panel 5.2 Hotkey Selection ( USB and/or PS/2 keyboard ) Note: If your keyboard is without < Scroll Lock > button, please press < Caps Lock > or instead of Scroll Lock ( ref. 5.2.0 ). 5.2.
You can synchronize the PC selection, by using the following two-step Hot Key sequence. To send commands to the Combo Free DVI KVM Switch, press the [Scroll] key twice (Step 1), then press key [1] or [2] or [3] and [Enter] (step 2) to assign the PC to a particular PC. ( If you press key [1] or [2] or [3] on the number pad, the keyboard, mouse & video will also be switched synchronously ) 5.2.2 Auto-Scan Function Hot Key: [Scroll] → [Scroll] → [S] → [Enter] to BEGIN.
5.2.3 Beeper Enable Hot Key: [Scroll] → [Scroll] → [B] → [Enter] to Disable [Scroll] → [Scroll] → [B] → [Enter] to Enable . The Speaker/Beeper’s default setting is “Enable”. While the switching connections are activated and Speaker/Beeper is in “Enable” status, the beeper has a short beeping sound. 5.3 Audio ( Speaker + Microphone ) Selection 5.3.
5.3.
Hot Key definition table Step 1 Step 2 Action [Scroll] + [Scroll] [1] + [ Enter ] [2] + [ Enter ] [3] + [ Enter ] Switch the active connection to PC 1 Switch the active connection to PC 2 Switch the active connection to PC 3 [A] + [ Enter ] [F1] + [ Enter ] [F2]+ [ Enter ] [F3] + [ Enter ] Disable or enable the Audio auto switch mode Combined switching (PC+Audio) to PC 1 Combined switching (PC+Audio) to PC 2 Combined switching (PC+Audio) to PC 3 [Scroll] + [Scroll] [Scroll] + [Scroll] [Scroll] + [Sc
Sun Microsystems Function Key Emulation: There are 16 special functions on the Sun Microsystems keyboard, the Combo Free DVI KVM Switch can emulate these function keys via the PS/2 and/or USB keyboard. Here is the mapping table for these functions operation. To active these emulation on the PS/2 and/or USB keyboard, you have to press the LEFT Window KEY first (this key usually is located between the left [Ctrl] and left [Alt]), then choice the second relative key.
Disclaimer Information in this document is subject to change without notice. The manufacturer does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial damage, including but not limited to special, incidental, consequential, or other damages.
