5.
TABLE OF CONTENTS Introduction 1 Features 2 Package Contents 2 Safety Warnings 3 Connections and Controls 4 Installation 5 Operation 7 Troubleshooting 10 Specifications 11 INTRODUCTION Thank you for purchasing the Monoprice 10247 Wireless Audio/Video Extender! For best results please read this manual carefully, paying extra attention to the safety warnings. Keep this manual in a safe place for future reference.
FEATURES Avoids the crowded 2.4GHz band by operating at 5.
SAFETY WARNINGS To avoid personal injury or damage to your equipment, please adhere to the following safety guidelines: 1. Do not expose this device to water or moisture of any kind. Do not place objects filled with liquids on or near this device. 2. Do not install this device in an enclosed space. Ensure that there is sufficient ventilation to keep the unit from overheating. 3. Do not place objects on this device or otherwise block the cooling vents. 4.
CONNECTIONS AND CONTROLS The following diagrams identify the various connections and controls on the Transmitter and Receiver units of the Extender: Transmitter Receiver Transmitter & Receiver (Rear view) Accessories Adaptor Transmitter and Receiver 1. RF Channel Selector 2. 5.8 GHz Antenna 3. ON / OFF Switch 4. Infrared Remote Output Jack 5. IR Frequency Selection Rear view of Transmitter & Receiver 6. Audio L 7. Audio R 8. Composite Video 9. S-Video 10.
INSTALLATION 1. Using one of the included video cables, connect the yellow, red, and white RCA plugs to the corresponding jacks on your DVD player (or other video source device). 2. Plug the other end of the video cable into the RCA jacks on the back of the Transmitter unit. Rear View Satellite Receiver Power Adaptor VCR ON/OFF Switch DVD S-Video cable RCA cable VCD Rear view of source device 3. (Optional) Plug the IR transmitter bulb into the Remote Out jack on the side of the Transmitter unit.
4. Plug the DC connector from one of the AC adapters into the DC 5V input on the back of the Transmitter unit. Plug the other end into a 100-120 VAC/60Hz power outlet. 5. Using one of the included video cables, connect the yellow, red, and white RCA plugs to the corresponding jacks on your TV. 7. Plug the other end of the video cable into the RCA jacks on the back of the Receiver unit. Rear View Power Adaptor ON/OFF Switch Rear View S-Video cable RCA cable 5 8.
OPERATION 1. Use the Channel Selection switch on the Transmitter to select one of the four wireless channels. Set the Channel Selection switch on the Receiver to the same channel. Transmitter Receiver Channel selection button must be set to the same channel on both the transmitter & receiver. 2. Pull the antenna out of the base of the Transmitter until the face is vertical. Rotate the antenna until the side with the dot (the inside part) is facing the location of the Receiver unit.
For best performance position the antennas so that they are face-to-face (the side with the dot). Receiver Transmitter Receiver IR Receiver TV For best IR reception performance the Receiver unit should be positioned so that the front is slightly ahead of the Television screen.
For best results, the remote control should be positioned within 15 degrees of the IR sensing window on the Receiver unit. Additionally, it should be no closer than 1 foot and no further than 15 feet.
TROUBLESHOOTING No picture or sound a) Check the power on/off switches on the Transmitter, Receiver, source device, and TV. b) Make sure the power plug and signal cables are pushed all the way in. c) Check that the transmitter & receiver are set to the same wireless channel. d) Make sure that all cables are connected as per the installation instructions. e) Ensure that the range between the transmitter and receiver is not excessive.
SPECIFICATIONS TRANSMITTER Output Level 13dBm (complies with CE) Operating Frequencies 5790, 5828, 5847, and 5866 MHz Modulation FM (Video and Audio) Video Input Level 1.0 V p-p Audio Input Level 1.0 V p-p S-Video Input Level Y:1Vpp, C:288mV Video Input Impedance 75 ohm Audio Input Impedance 2K ohm Power Consumption DC 12V@250mA Unit Dimensions 4.7" x 3.9" x 1.7" (12 x 10 x 4.3 cm) Unit Weight 7.1 oz. (200g) Effective Operating Range Approx.
