Spec Sheet
FLUSH INSET INSTALLATION
SIDE VIEW
(WITH ACCESSORY TRIM)
23 9/16” Min
Flush inset depth
Top cleat
Bottom cleat
(Bottom cleat is set
back from top and
side cleats.)
2 3/4”
Side cleat
A
5 5/8”
Anti-Tip
Block
For questions about your
appliance, please call 1-800-626-2000.
PAGE 5 OF 7 Product Specication Revised 10/21
INSTALLATION WITH BOTTOM TRIM
PRODUCT FRONT VIEW
PRODUCT TOP VIEW
PRODUCT SIDE VIEW
29 3/4”
28 1/8”
23 7/16”
1 7/16”
22”18 13/16”
6 11/16”
5 13/16”
*1/2”
*
Drawer has 1/2”
gap visible on
side when closed.
FLUSH INSET INSTALLATION
TOP VIEW
(WITH ACCESSORY TRIM)
FLUSH INSET INSTALLATION
FRONT VIEW
(WITH ACCESSORY TRIM)
1 7/16”
Top & side cleat depth
FLUSH INSET INSTALLATION
SIDE VIEW
(WITH ACCESSORY TRIM)
23 9/16” Min
Flush inset depth
Top cleat
Bottom cleat
(Bottom cleat is set
back from top and
side cleats.)
28 1/2”
Cutout width
2 3/4”
Bottom cleat depth
3/4”
Side cleats
1/2”
Top cleat
5 15/16”
Opening
height
8 1/4”
Flush inset
height
6 5/16”
Side cleat
height
*1 3/4”
1 13/16”
Bottom cleat extends full
depth of cabinet and is set
back
2 3/4” from cabinet face.
2 3/4”
30” flush inset width
with
1/8” reveals
Side cleat
Side cleatSide cleat
*Side cleats must
allow 1 3/4” bottom
clearance for
bracket and trim.
Bottom cleat can be
either solid platform
or 4” wide runners.
FLUSH INSET INSTALLATION
TOP VIEW
(WITH ACCESSORY TRIM)
FLUSH INSET INSTALLATION
FRONT VIEW
(WITH ACCESSORY TRIM)
1 7/16”
Top & side cleat depth
FLUSH INSET INSTALLATION
SIDE VIEW
(WITH ACCESSORY TRIM)
23 9/16” Min
Flush inset depth
Top cleat
Bottom cleat
(Bottom cleat is set
back from top and
side cleats.)
28 1/2”
Cutout width
2 3/4”
Bottom cleat depth
3/4”
Side cleats
1/2”
Top cleat
5 15/16”
Opening
height
8 1/4”
Flush inset
height
6 5/16”
Side cleat
height
*1 3/4”
1 13/16”
Bottom cleat extends full
depth of cabinet and is set
back
2 3/4” from cabinet face.
2 3/4”
30” flush inset width
with
1/8” reveals
Side cleat
Side cleatSide cleat
*Side cleats must
allow 1 3/4” bottom
clearance for
bracket and trim.
Bottom cleat can be
either solid platform
or 4” wide runners.
PRODUCT FRONT VIEW
PRODUCT TOP VIEW
PRODUCT SIDE VIEW
29 3/4”
28 1/8”
23 7/16”
1 7/16”
22”18 13/16”
6 11/16”
5 13/16”
*1/2”
*
Drawer has 1/2”
gap visible on
side when closed.
PRODUCT FRONT VIEW
PRODUCT TOP VIEW
PRODUCT SIDE VIEW
29 3/4”
28 1/8”
23 7/16”
1 7/16”
22”18 13/16”
6 11/16”
5 13/16”
*1/2”
*
Drawer has 1/2”
gap visible on
side when closed.
HELPFUL TIPS
A
Install an anti-tip block against rear
wall, 5 5/8" from oor of cutout to
bottom of block. The anti-tip block
must be installed to prevent the drawer
from tipping forward when opened and
loaded. Failure to add the anti-tip block
could result in personal injury.
B
When installing the storage drawer
below a cabinet drawer, a solid barrier
must be installed at least above the
storage drawer to block access. Use any
solid material such as 1/4" thick plywood.
Allow at least 1/4" air gap between the
barrier and the top of the storage drawer.
Observe the 3/8" min. above the toe kick
installation height.
C
The storage drawer may be supported by
either a solid bottom or 2"x2" or 2"x4"
runners. The support must be level and
rigidly mounted, ush with the bottom
edge of the cut-out (there is no way
to level the drawer once it has been
installed, so make sure that the supports
are level). The oor or runners must be
capable of supporting at least 65 lbs.
D
Cabinet surfaces must be an appearance
nished surface for ush installation.
E
Cleats may be visible and should be
nished to match cabinetry.
For more details refer to the installation
instructions for this product.
B
EC D