Installation Guide

12 31-2000856 Rev. 0
Installation Instructions
2A
INSTALL HOOD ONTO WALL
SKIP THIS STEP IF INSTALLING BENEATH A
SOFFIT OR CABINET, GO TO STEP 2B.
Ŷ/RFDWHDWOHDVWYHUWLFDOVWXGVDWWKHZRRGVXSSRUW
Ŷ&HQWHUWKHVXSSOLHGZRRGVXSSRUWOHIWWRULJKWDQG
below the 20" marked line.
Ŷ6HFXUHWKHZRRGVXSSRUWWRRUPRUHYHUWLFDOVWXGV
using at least 2 of the 4 supplied long screws.
IMPORTANT: Screws must penetrate at least 1-1/2" into
vertical studs. Countersink screws into support.
NOTE: The mounting screws must remain in their
original shipping location. These screws are positioned
to engage the keyhole slots in the back of the hood.
Ŷ$GMXVWGHSWKRIRULJLQDOPRXQWLQJVFUHZVLQWKHZRRG
support until they protrude 1/4" forward. This 1/4" gap
will provide clearance to hang the hood.
Install Transition Onto Top of Hood
IMPORTANT: Remove shipping tape from damper and
check that damper moves freely.
Ŷ3ODFHWKHGXFWWUDQVLWLRQSLHFHRYHUWKHKRRGH[KDXVW
and secure with 4 screws
provided.
Ŷ8VHGXFWWDSHWRVHDOWKH
connection. Check to be sure
the damper moves freely.
Hang Hood On Wood
Support
Ŷ/LIWWKHKRRGDQGKROGFORVHWRWKHLQVWDOODWLRQORFDWLRQ
Route house wiring through the knockout and into the
MXQFWLRQER[
Ŷ3ODFHWKHKRRGRYHUWKHZRRGVXSSRUW%HVXUHWKH
mounting screws engage the keyhole slots in the back
of the hood. Tighten the screws.
WARNING
Continue to provide additional support
while the hood is mounted with only these 2 screws.
These screws will not support the weight of the hood. The
hood could fall resulting in damage or personal injury.
AVERTISSEMENT
Continuez à fournir un soutien
DGGLWLRQQHOSHQGDQWOHPRQWDJHGHODKRWWHDYHFFHVGHX[
YLVVHXOHPHQW&HVGHX[YLVQHVRXWLHQGURQWSDVOHSRLGVGH
ODKRWWH/DKRWWHSHXWWRPEHURFFDVLRQQDQWGHVEOHVVXUHV
corporelles ou des dommages matériels.
ADVERTENCIA
$JUHJXHVRSRUWHDGLFLRQDOFXDQGROD
campana sea montada sólo con estos 2 tornillos. Estos tornillos
QRVRSRUWDUiQHOSHVRGHODFDPSDQD/DFDPSDQDSRGUiFDHU
produciendo daños o lesiones personales.
Ŷ&KHFNWREHVXUHWKHKRRGLVOHYHODQGFHQWHUHG
Test Duct Cover Fit
Ŷ3ODFHGXFWFRYHUV
over the top of the
hood to check for
JDSV$GMXVWWKH
hood up or down if
necessary.
Install Bottom
Mounting Screws
Ŷ'ULOOSLORWKROHVLQWRWKHWZRORZHUPRXQWLQJ
holes. Enlarge the holes if they did not enter studs
to 3/8". Insert anchors for wall fasteners into bottom
holes. Remove anchor screws and add flat washers
provided. Drive screws into anchors and tighten.
Ŷ,QVWDOODGGLWLRQDOVFUHZVWKURXJKWKHEDFNRIWKH
hood and into the wood support.
Centerline of
Installation
Space
20"
Bottom
of
Hood
Wood
Support
1/4"
Gap
Original Mounting
Screws as Shipped
Duct
Transitio
n
Top of
Hood
Centerline of
Installation
Space
Bottom
Mounting
Holes
30"
to
36"
IMPORTANT:)UDPLQJPXVWEHFDSDEOHRI
supporting up to 150 lbs.