Specification Sheet

PAGE 4 OF 5 Product Specication Revised 8/20
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout depth
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
2" (5.1) x 4" (10.2)
or Equivalent Runners
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30" (76.2)
25" (63.5)
23 1/2"
(59.7)
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
ZTW900SSNSS
For questions about your
appliance, please call 1-800-626-2000.
A
If you are installing in frameless cabinets,
it may be necessary to install 1/2" wide
cleats to accept drawer mounting screws.
See drawer for mounting screw locations.
B
Install a 2"x2" or 2"x4" anti-tip block
against rear wall, 9" from floor of cutout
to bottom of block. e anti-tip block
must be installed to prevent the drawer
from tipping forward when opened and
loaded. Failure to add the anti-tip block
could result in personal injury.
C
When installing the warming drawer
below a cabinet drawer, a solid barrier
must be installed at least above the
warming drawer to block access. Use any
solid material such as 1/4" thick plywood.
Allow at least 1/4" air gap between the
barrier and the top of the warming
drawer. Observe the 5" min. above
the floor or 1" min. above the toe kick
installation height.
D
When installing two warming drawers
side by side, install them in separate
cut-outs and allow a 2" min. gap between
each cut-out.
E
e warming drawer may be supported
by either a solid bottom or 2"x2" or 2"x4"
runners. e support must be level and
rigidly mounted, flush with the bottom
edge of the cut-out (there is no way to
level the drawer once it has been installed,
so make sure that the supports are level).
e floor or runners must be capable of
supporting at least 150 lbs.
For more details refer to the installation
instructions for this product.
PROVIDING CABINET SUPPORT INSTALLING ANTI-TIP BLOCKS
SIDE BY SIDE INSTALLATION
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout depth
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
2" (5.1) x 4" (10.2)
or Equivalent Runners
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30" (76.2)
25" (63.5)
23 1/2"
(59.7)
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
ZTW900SSNSS
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout depth
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
2" (5.1) x 4" (10.2)
or Equivalent Runners
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30" (76.2)
25" (63.5)
23 1/2"
(59.7)
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
ZTW900SSNSS
A
A
D
E
B
B
C
HELPFUL TIPSINSTALLATION BELOW A CABINET DRAWER