CTS90DM2NS5 CTD90DM2NS5 ZTS1DNSS ZTD1DNSS

ManualsBrandsMonogram ManualsDouble Wall OvensMonogram Minimalist Collection 30" Stainless Steel Smart Electric Convection Double Wall Oven

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

•

IMPORTANT — Save these

instructions for local inspector’s use.

•

IMPORTANT — Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with Consumer.

• Note to Consumer – Keep these

instructions for future reference.

• Skill level – Installation of this appliance

requires a qualified installer or electrician.

• Proper installation is the responsibility

of the installer.

• Product failure due to improper installation

is not covered under Warranty.

• Product is for indoor use only.

Installation Instructions

30” Electric Push-to-Open Door

Built-In Wall Ovens

FOR YOUR SAFETY:

WARNING

Before beginning the installation, switch power off at the service panel and lock

the service disconnecting means to prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a

tag, to the service panel.

Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight

on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,

stand or hang on the oven door.

Make sure the wall coverings, counters and cabinets around the oven can withstand the heat (up to

200°F [93.3°C]) generated by the oven.

MATERIALS YOU MAY NEED

Junction Box

Wire Nuts

Strain Relief Clamp for 1/2” Conduit

36” (91 cm) of String

TOOLS YOU MAY NEED

1/8” Drill Bit and Electric or Hand Drill

T20 Screwdriver

Phillips Screwdriver

Wire Strippers

7/16” Nut Driver (combination ovens)

1/4” Nut Driver (30” combination ovens)

REMOVE PACKAGING MATERIALS

Failure to remove packaging materials could result in damage to the appliance. Remove all

packing parts from oven, racks and heating elements. Remove protective film and labels on

the outer door and control panel. Also, remove plastic on trims and panel, all tape around the

oven and any shipping screws securing the oven to the base pad. Open oven door and remove

literature pack and oven racks. Remove the bottom trim from the top of the oven. It will be

installed at the end of the installation process. The trim is wrapped separately and taped to the top

of the unit. Remove pedestal rails from separate box and set aside (30” Double Wall Ovens Only).

PREPARE THE OPENING

NOTE: If the cabinet does not have a solid

bottom, two braces or runners must be

installed to support the weight of the oven.

For single ovens, the runners and braces

must support 220 lbs (99 kg). For double and

combination ovens, the runners and braces

must support 400 lbs. (181 kg).

NOTE: If marks, blemishes or the cutout

opening are visible above the installed oven,

it may be necessary to add wood shims

under the runners until the marks or opening

are covered.

NOTE: If the cabinet does not have a front

frame and the sides are less than ¾” (1.9 cm)

thick, shim both sides equally to establish the

cutout width.

ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired)

into an approved junction box. A plug and receptacle is NOT permitted on these products.

DESIGN INFORMATION

SINGLE OVEN INSTALLATIONS

The single oven may be installed in a cabinet alone or above a warming drawer. The single oven

may also be installed side by side. However, the Push-to-Open single wall oven is not allowed

under a counter unit or cooktop. See the label on top of the oven for approved models.

DOUBLE OVEN INSTALLATIONS

A double oven may be installed in a cabinet alone or above a warming drawer. See the label on

top of the oven for approved models.

IMPORTANT: Always refer to individual installation instructions packed with each product for

specific requirements.

Questions? Call us at 1.800.432.2737 or visit GEAppliances.com.

In Canada, call 1.800.561.3344 or visit GEAppliances.ca.

Suitable

Bracing

to Support

Runners

2" x 4" (5 cm x 10 cm)

or Equivalent Runners Level

with Bottom of Cutout

and Flush with Sides of Cutout

Summary of content (16 pages)

PAGE 1
Installation Instructions 30” Electric Push-to-Open Door Built-In Wall Ovens Questions? Call us at 1.800.432.2737 or visit GEAppliances.com. In Canada, call 1.800.561.3344 or visit GEAppliances.ca. BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT — Save these instructions for local inspector’s use. • IMPORTANT — Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with Consumer.
PAGE 2
A CUTOUT FOR SINGLE OVENS IN WALL CABINET 2 B CUTOUT FOR DOUBLE OVENS (2 THERMAL NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim both sides equally to establish the cutout width. Junction These ovens are not approved for installations that stack one single wall oven above another single wall oven.
PAGE 3
2 C CUTOUT FOR INSTALLATION OVER A WARMING DRAWER 3 A DETERMINING WHEN TO USE THE PEDESTAL (30” DOUBLE OVENS ONLY) NOTE: Install the oven only with specific models listed on the label located on top of the oven. NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height.
PAGE 4
DOOR REMOVAL (RECOMMENDED FOR THERMAL OVENS) WARNING WARNING The door for the microwave oven on a combination oven should never be removed, unless by a certified technician. Hinge Bracket NOTE: Door removal is not a requirement for installation of the product but is an added convenience. To remove the door: A. Open the oven door as far as it will go. B. Remove hinge bracket, if equipped, from front frame and set aside.
PAGE 5
6 MAKE ELECTRICAL CONNECTIONS 8 FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION WARNING Switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. Place oven on table or platform even with the cutout opening. For a single oven, the platform must support 220 lbs.
PAGE 6
10 INSTALL MOUNTING SCREWS (THERMAL OVENS) 12 OVEN RACK GUIDE INSTALLATION (IF APPLICABLE) A. Locate included oven rack guide mouting hardware. B. Place oven rack guides on cavity wall studs with metal posts towards back of cavity as shown. C. Install guides using the 8 provided mounting nuts. WARNING Mounting screws must be used. Failure to do so could result in the oven falling out of the cabinet, causing serious injury.
PAGE 7
13 REPLACING THE THERMAL OVEN DOOR 14 FINAL INSTALLATION CHECKLIST NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. A. Lift the oven door by grasping each side. B. With the door at the same angle as the removal position (approximately 1”–2” [2.5 cm–5.1 cm] from the closed position), seat the notch of the hinge arm into the bottom edge of the hinge slot.
PAGE 8
PAGE 9
Instrucciones de instalación Hornos Eléctricos de 30” con Puerta de Apertura con Empuje Empotrados en Pared ¿Preguntas? Comuníquese con nosotros al 1.800.432.273 o visita GEAppliances.com. En Canadá, llame 1.800.561.3344 o visita GEAppliances.ca. ANTES DE COMENZAR Lea estas instrucciones por completo y con detenimiento. • IMPORTANTE – Guarde estas • IMPORTANTE – Cumpla con todos los • códigos y ordenanzas vigentes. Nota al instalador – Asegúrese de dejar estas instrucciones con el Consumidor.
PAGE 10
2 A 2 B ABERTURA PARA HORNOS ÚNICOS EN UN GABIENTE DE PARED NOTA: Si el gabinete no cuenta con un armazón frontal y los lados son menores a un grosor de 3/4” Ubicanción H sobre (1,9 cm), coloque cuñas uniformemente de laambos caja de lados para establecer al ancho Estos hornos de la abertura. conexiones (la caja de no están conexiones aprobados B puede hallarse para R en un gabinete adyancente) instalaciones apilables.
PAGE 11
2 C ABERTURA PARA INSTALACIÓN SOBRE UN CAJÓN CALENTADOR NOTA: Instale el horno sólo con los modelos específicos listados en la etiqueta ubicada en la parte superior del horno. NOTA: Pueden necesitarse espacios adicionales entre las aberturas. Verifique que los soportes del horno sobre la ubicación de cajón calentador no obstruyan la profundidad y altura interiores requeridas.
PAGE 12
4 REMOCIÓN DE LA PUERTA (RECOMENDADO PARA HORNOS TÉRMICOS) ADVERTENCIA La puerta del horno microondas en un horno combinado nunca debe ser retirada, a menos que esto sea realizado por un técnico certificado. Soporte de la Bisagra NOTA: La remoción de la puerta no es un requerimiento de la instalación del producto, pero es una comodidad adicional. Para quitar la puerta: REQUISITOS ELÉCTRICOS ADVERTENCIA ADVERTENCIA Este aparato debe contar con una adecuada conexión a tierra.
PAGE 13
6 8 REALICE LAS CONEXIONES ELÉCTRICAS ADVERTENCIA Desconecte la energía del panel de servicio y bloquee los medios de desconexión para evitar el accionamiento de la energía de manera accidental. Cuando los medios de desconexión de servicio no pueden bloquearse, coloque sobre el panel de servicio un dispositivo de advertencia bien visible, como una etiqueta. Coloque el horno sobre una mesa o plataforma en forma nivelada con la abertura. Para un horno único, la plataforma debe soportar 220 lbs.
PAGE 14
10 INSTALE LOS TORNILLOS DE MONTAJE (HORNOS TÉRMICOS) 12 GUÍA DE INSTALACIÓN DE LA ESTANTERÍA DEL HORNO (SI CORRESPONDE) A. Ubique el equipo de montaje de la guía del horno incluida. ADVERTENCIA B. Coloque las guías de los estantes del horno en los montajes de pared de la cavidad con los postes metálicos hacia la parte trasera de la cavidad, como se muestra. Deben utilizarse tornillos de montaje. Si no lo hace, el horno puede caer del gabinete, lo que provocaría una lesión grave. C.
PAGE 15
13 REEMPLAZO DE LA PUERTA TÉRMICA DEL HORNO 14 LISTA DE CONTROL FINAL DE LA INSTALACIÓN NOTA: La puerta del horno es pesada. Puede necesitar ayuda para levantar la puerta lo suficiente como para deslizarla dentro de las ranuras de la bisagra. No levante la puerta de la manija. • Verifique que el interruptor de circuitos se encuentre cerrado (RESET) o que los fusibles del circuito se hayan reemplazado. A. Levante la puerta del horno tomándola de ambos lados.
PAGE 16