Specification Sheet
For questions about your
appliance, please call 1-800-626-2000.
HELPFUL TIPS
Product Specication Created 10/19PAGE 3 OF 5
STANDARD INSTALLATION
ANTI-TIP BRACKET
Use two
additional hole
locations at
end of
brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
23 5/8" (60)
2 3/8"
(6)
4 7/16"
(11.3)
7/16"
(1.1)
Trim overlap
35 1/2" (90.2)
2 5/16"
(5.9)
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
E
6"
(15.2)
10"
(25.4)
SIDE VIEW
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
ZICS360NXRH
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0)
10" (25.4)
WATER
FRONT VIEW
81 1/2"
(207.0)
ZICS360NXLH
Use two
additional hole
locations at
end of
brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
35 1/2" (90.2)
2 5/16"
(5.9)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
SIDE VIEWFRONT VIEW
ELEC.
6"
(15.2)
10"
(25.4)
23 5/8" (60)
2 3/8"
(6)
4 7/16"
(11.3)
7/16
"
(1.1)
Trim overlap
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0)
WATER
10" (25.4)
81 1/2"
(207.0)
A
B
A
Mounting the junction box in this
location will also allow for front
accessability through access panel.
B
Water supply area.
WARNING:
e refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
e information below is for cabinet
design only. When installing the anti-
tip system you must use the product
installation instructions.
e information below applies to all
installation constructions:
• A wall bracket, bolts and toggles will
be supplied with the unit.
• e bolts will be used to attach
bracket to wall in 4 locations. Two
of the locations must penetrate the
center of the wall studs.
• e toggles are used for stability in
drywall and when metal studs are
encountered. Lag bolts are used in
wood studs.
• In installation opening, measure
81-1/2" from floor and draw a
horizontal line.
• Locate and mark the wall studs on
horizontal line. Verify at least two
studs have their centerlines within the
center 32-1/2" of installation opening
to ensure 2 wall studs are penetrated.
• e bracket will be centered left to right
in opening with bottom of bracket on the
horizontal line.
• When unit is placed in opening, the
bracket tabs will align with openings
in back of the unit. e unit will be
secured to the bracket using supplied
“L” bolts.
See Installation Instructions for
detailed instructions.