Quick Specification
PAGE 4 OF 14 Product Specication Revised 10/20
STANDARD INSTALLATION
ZISB480DH
24" (61)
1 9/16"
(3.97)
47 1/2" (120.7)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
*84
+
-
.500
(212.1-214.6)
*Trim will overlap
additional 7/16"
SIDE VIEW
FRONT VIEW
TOP VIEW
5"
(12.7)
5"
(12.7)
WATERW
6 3/4"
(17.1)
20" (50.8)
6 3/4"
(17.1)
E
HELPFUL TIPS
For questions about your
appliance, please call 1-800-626-2000.
STANDARD INSTALLATION
STANDARD INSTALLATION
ANTI-TIP BRACKET
FRONT VIEW SIDE VIEW
W
24" (61.0)
1 1/2"
(3.8)
3 1/4"
(8.3)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISB480DX
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
Top Case Trim
3/4"
Min.
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
D
C
E
A
B
A
Mounting the junction box in this
location will also allow for front
accessibility through access panel.
B
Water supply area.
WARNING:
e refrigerator is top heavy
and must be secured to prevent
the possibility of tipping forward.
Failure to do so may result in death
or serious injury.
e information below is for cabinet
design only. When installing the anti-
tip system you must use the product
installation instructions.
Determine your installation construction
and required anti-tip configuration:
C
Installed Under Soffit
After installing unit into installation
opening, raise grille panel and screw
metal case sides to adjacent cabinet.
When installed under a soffit, the
soffit cannot exceed 24" deep. e top
case trim overlaps the bottom
of the soffit.
D
Wooden Wall Studs and No Soffit
• Cut a 2" x 4" block and secure to
brackets provided.
• Secure brackets to back wall of
opening at 84" or your installation
height from the floor.
E
Metal Wall Studs and No Soffit
is method requires securely
fastened cabinets on both sides and
a 3/4" minimum wood brace above
unit, with it’s front surface 24" from
back wall.
• After installing unit into opening,
raise grille panel and attach metal
case top trim to 3/4" minimum
wood brace.
• e brace spanning the enclosure
must be securely fastened to
cabinets on both sides.
See Installation Instructions for
detailed instructions.
e refrigerator will project forward, slightly beyond adjacent cabinetry.