Quick Specs
HELPFUL TIPS
For questions about your
appliance, please call 1-800-626-2000.
Product Specication Created 10/19
STANDARD INSTALLATION
PAGE 4 OF 14
STANDARD INSTALLATION
ANTI-TIP BRACKET
FRONT VIEW SIDE VIEW
W
24" (61.0)
1 1/2"
(3.8)
3 1/4"
(8.3)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISB480DX
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
Top Case Trim
3/4"
Min.
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
D
C
E
STANDARD INSTALLATION
ZISB420DH
24" (61)
1 9/16"
(3.97)
41 1/2" (105.4)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
*84 1/2"
(214.6)
*Trim will overlap
additional 7/16"
SIDE VIEW
FRONT VIEW
TOP VIEW
5"
(12.7)
5"
(12.7)
WATERW
E
18" (45.7)
6"
(15.24)
5"
(12.7)
A
B
e refrigerator will project forward, slightly beyond adjacent cabinetry.
A
Mounting the junction box in this
location will also allow for front
accessibility through access panel.
B
Water supply area.
WARNING:
e refrigerator is top heavy
and must be secured to prevent
the possibility of tipping forward.
Failure to do so may result in death
or serious injury.
e information below is for cabinet
design only. When installing the
anti-tip system you must use the
product installation instructions.
Determine your installation
construction and required
anti-tip configuration:
C
Installed Under Soffit
After installing unit into
installation opening, raise grille
panel and screw metal case sides
to adjacent cabinet. When installed
under a soffit, the soffit cannot
exceed 24" deep. e top case trim
overlaps the bottom of the soffit.
D
Wooden Wall Studs and No Soffit
• Cut a 2" x 4" block and secure to
brackets provided.
• Secure brackets to back wall
of opening at 84" or your
installation height from the floor.
E
Metal Wall Studs and No Soffit
is method requires securely
fastened cabinets on both sides
and a 3/4" minimum wood brace
above unit, with it’s front surface
24" from back wall.
• After installing unit into opening,
raise grille panel and attach
metal case top trim to 3/4"
minimum wood brace.
• e brace spanning the enclosure
must be securely fastened to
cabinets on both sides.
See Installation Instructions for
detailed instructions.