Specifications

STANDARD INSTALLATION
ANTI-TIP BRACKET
ZIFS360NHRHMONOGRAM 36" BUILT-IN ALL-FREEZER
Product Specification Revised 1/18
SIDE VIEW
W
24" (61.0 )
2"
(5.1)
4"
(10.2)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
FRONT VIEW
ELEC.
35 1/2" (90.2)
2 5/16"
(5.9)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75 1/2 "
(191.8)
From floor
to bottom
of electrical
area
5 1/2"
(14.0)
9"
(22.9)
ZIFS360NXRH
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
5"
(12.7)
5"
(12.7)
WATER
3 1/2"
(9.0)
81 1/2"
(207.0)
Use two
additional hole
locations at end
of brackets
Wall
Studs
Screws
mounted
into vertical
wall studs
C
Make sure
holes selected
are centered
on the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
SIDE VIEW
W
24" (61.0 )
2"
(5.1)
4"
(10.2)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
FRONT VIEW
ELEC.
35 1/2" (90.2)
2 5/16"
(5.9)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75 1/2 "
(191.8)
From floor
to bottom
of electrical
area
5 1/2"
(14.0)
9"
(22.9)
ZIFS360NXRH
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
5"
(12.7)
5"
(12.7)
WATER
3 1/2"
(9.0)
81 1/2"
(207.0)
Use two
additional hole
locations at end
of brackets
Wall
Studs
Screws
mounted
into vertical
wall studs
C
Make sure
holes selected
are centered
on the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
A
A
Mounting the junction
box in this location
will also allow for front
accessibility through
access panel.
B
Water supply area.
WARNING:
The freezer is top heavy
and must be secured to
prevent the possibility of
tipping forward. Failure to
do so may result in death or
serious injury.
The information below is for
cabinet design only. When
installing the anti-tip system
you must use the product
installation instructions.
The information below
applies to all installation
constructions:
• A wall bracket, bolts and
toggles will be supplied
with the unit.
• The bolts will be used to
attach bracket to wall in
4 locations. Two of the
locations must penetrate
the center of the wall
studs.
• The toggles are used for
stability in drywall and
when metal studs are
encountered. Lag bolts
are used in wood studs.
• In installation opening,
measure 81.5" from
floor and draw a
horizontal line.
• Locate and mark the wall
studs on horizontal line.
Verify at least two studs
have their centerlines
within the center 32.5”
of installation opening to
ensure 2 wall studs are
penetrated.
• The bracket will be
centered left to right in
opening with bottom of
bracket on the horizontal
line.
• When unit is placed in
opening, the bracket tabs
will align with openings
in back of the unit. The
unit will be secured to the
bracket using supplied “L”
bolts.
See Installation Instructions
for detailed instructions.
NOTES
B