Specifications

ZIF360NHLHMONOGRAM 36" BUILT-IN ALL-FREEZER
Product Specification Revised 1/18
NOTES
A
In a side-by-side installation of a left-
and-right-hand door swing product,
1" clearance between the units is
required.
Order ZUG2: Custom panel unified grille
kit for one continuous grille panel.
B
In a side-by-side installation with
same door swing, allow 2" minimum
clearance between the products to
prevent the door swing interference.
Allow 15" minimum to a wall to
achieve full drawer extension and
pan removal. Additional clearances
are required when using custom
panels and handles.
NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille
panel kits will not fit this installation.
C
In a side-by-side installation with
right and left door hinges together,
allow 5” minimum clearance between
the two products to prevent
one door from striking the other.
Additional clearances required when
using custom panels and handles.
NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille
panel kits will not fit this installation.
DUAL PRODUCT CLEARANCES
71 1/2" (181.6)
Finished Width
24" (61.0)
Min. Cutout Depth
24 3/16" (61.4)
2 5/16"
(5.9)
5 1/2"
(13.9)
9"
(22.9)
83 1/2" min
84 1/2" max
(212.1-214.6)
Finished Opening
3 1/2"
(8.9)
ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH
ZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH
W
FRONT VIEW
ELEC.
5 1/2"
(13.9)
9"
(22.9)
3 1/2"
(8.9)
25" (63.5) min
To wall
25" (63.5) min
To wall
5" (12.7) min
15"
(38.1) min
To wall
1"
(2.5)
2" min
(5.1)
130˚
Door swing
130˚
Door swing
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
5"
(12.7)
5"
(12.7)
5"
(12.7)
5"
(12.7)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
A B
C
STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION
PANEL ASSEMBLY
CROSS SECTION
PANEL DIMENSIONS
1/4"
Backer
Panel
.10"
Spacer
Panel
3/4"
Overlay
Panel
A 69 7/8" 68 1/2" 70 1/8"
B 8 7/8" 7 5/8" 9"
C 69 5/16" 67 15/16" 69 9/16"
D 33 7/8" 32 1/2" 34 1/8"
.25" + .10" + .75" =
1.10" Total Panel Thickness
Grille Panel
Door
Panel
D
A
Door
Panel
B
C
D
Door
1/4" Backer Panel
.10" Spacer Panel
Supplied Handles
Trim
3/4" Overlay Panel
3/4" Overlay Panels: For 3/4" thick
custom panels ordered from your
cabinet maker. The decorative panels
slide into the trim. The overlay panel
must be secured to a 1/4"-thick backer
panel which slides into the trim. A
spacer panel 0.10" thick must be placed
between the overlay and backer panels.
Center each panel over the other.
Assemble the panels with glue and
screws. Screws must be countersunk
into the backer panel.
NOTE: Left-to-right oset is not always
equal to top-to-bottom oset.
Maximum total panel weight:
• Door panel – 67 lbs.
• Grille panel – 25 lbs.
Order ZUG2: Unified grille kit for dual
installation. Maximum total panel
weight - 25 lbs.
Door Handles: The supplied handles
can be adjusted to accommodate
both framed or overlay panels. Custom
handles of your choice, supplied
by your cabinet maker, can also be
installed.
ZKHPSS1: Professional stainless steel
handle designed to fit 3/4" overlay
panels. Kits include one handle -
30 1/2" long.
ZKHSS2: European stainless steel
handle designed to fit 3/4" overlay
panels. Kits include one handle -
64 1/4" long.
STANDARD
INSTALLATION