Installation Instructions ProfessionalRanges 48" Natural Gas Models ZDP48N4G ZDP48N6R ZDP48N6D 48" LP Gas Models ZDP48L4G ZDP48L6R ZDP48L6D 36" Natural Gas Models ZDP36N6 ZDP36N4R ZDP36N4D 36" LP Gas Models ZDP36L6 ZDP36L4R ZDP36L4D 30" Natural Gas Model ZDP30N4 30" LP Gas Model ZDP30L4 Monogram.
Installation Instructions BEFORE YOU BEGIN CAUTION: Read these instructions completely and carefully. THESE RANGES SHOULD BE INSTALLED IN CONJUNCTION WITH A SUITABLE • IMPORTANT- savethese OVERHEAD VENT HOOD. Due to the high heat capacity of this unit, particular attention should be paid to the hood and duct work installation to assure it meets instructions for local inspector's use, local building codes. • IMPORTANT - Observe all governing codes and ordinances.
Design Information CONTENTS Installation Instructions Step 1, Remove Packaging ..............................................8 Step 2, Level the Range ....................................................9 Step 3, Install Anti-Tip Device ..................................9, 10 Step 4, Connect Range to Gas ......................................11 Step 5, Connect Electrical ..............................................12 Step 6, Slide Range into Position ................................
Design Information PRODUCT DIMENSIONS AND CLEARANCES 48"Wide RangeModels 36"Wide RangeModels _:::::::::::::±_:::::::::::::::::_:_:_:::_:_ 22 _ 35-1/4"-36-3/4" < N 28-1/4'_ _35-7/8" 48"and 36"RangeModels 9 1/2"_ 12"Min. to Combustiblesor l/' 0" Min. to Combustibles with 12" or 22" Backsplash 36" Min. to Combustibles 29-1/16''_ -3/4"_ / ",_ 22" High Backsplash with Shelf 22" 36" Min. to Combustibles ._Backguard _12" HighBacksplash • J 0" Clearance ' r'7 r" "3 NOTE: 12" Min.
Design Information PRODUCT DIMENSIONS AND CLEARANCES 30"Wide RangeModels 9-1/2" 3/4"_ 22" 27-3/8"_ _--22" High Backsplash with Shelf 36" Min. to Combustibles Backsplash -?I [_29-1/4"_ I_ 43-7/8" NOTE: Refer to Vent Hood Installation Instructions for hood height above the range. o o O t 1-1/2" ElectricalSupply GasSupply [ .................. • "_ 35-3/8"Max. for CounterLevel 36-3/4"Max.
Design Information ADVANCE PLANNING TOOLS REQUIRED • Saw Refer to "Dimensions and Clearances" for appropriate placement and necessary clearances when planning the installation. • Measuring tape • Carpenter's square • Cabinetry can not be installed directly above the range. • Pipe wrench • Large flat-blade screwdriver • We recommend the installation of a vent hood above the surface. - The vent hood must be at least 24" deep.
Installation POWER SUPPLY LOCATIONS If the electrical service provided does not meet the above specifications, it is recommended that a licensed electrician install an approved outlet, Gas Supply: • The natural gas models are designed to operate at 5" water column pressure. A regulator is required at the natural gas source to provide a maximum of 7" water pressure to the cooktop regulator, • The liquid propane models are designed to operate at 10"water column pressure.
Installation STEP 1 REMOVE PACKAGING Slot Before moving the range indoors: • Remove outer carton and packing material from the shipping base, PulI the hinge locks down to unlock. Remove oven doors: • Fully open the door. • Each hinge has a hinge lock, Close the hinge latch down against the door frame. • Firmly grasp the door at the top sides. Kick Panel • Close the door to the near-vertical • Remove the kick panel by removing 2 screws atthe top and pulling forward. position.
Installation STEP 2 LEVEL THE RANGE NOTE: Rear range leveling legs are not accessible after installation. • Adjust the height of the range to countertop height or higher. • Check to be sure the adjoining cabinets/countertops are level, front to back and left to right across the opening of the range. IMPORTANT: The range should always be installed at countertop height or higher. DO NOT INSTALL THE RANGE LOWER THAN ADJACENT COUNTERTOP HEIGHT.
Installation STEP 3 INSTALL ANTI-TIP (CONTINUED) DEVICE SmallHoleForWood (2) WoodScrewsinto BackWall Installations(2 Total) (All Installations) (2) LargeHolesFor ConcreteInstallations Back Wall SmallHolesForWood Installations(2 Wood Slide Strip Dimension A 1/4" 5/8" ZDP36 ZDP30 Wood Construction: Concrete or Cement Construction: • Place the bracket against the back wall, into the right rear corner of the installation location.
Installation STEP 4 CONNECT RANGE TO GAS Assure that gas supply is turned off at the shut-off valve: Do not use a flame to check _k_ CAUTION: • Connect flexible metal connector to incoming gas line pipe stub located on the left side on the bottom back of the range. MISE EN GARDE : II ne faut pas utiliser de flamme pour v_rifier s'il y a des fruites. • Turn on gas and check for leaks: - Use a liquid leak detector at all joints and connections in the system. o o o o for gas leaks.
Installation STEP 5 CONNECT ELECTRICAL STEP 7 Plug power cord into properly grounded receptacle, REPLACE OVEN DOOR(S) IMPORTANT: Do not lift the door by the handle. To replace the oven doors: STEP 6 • Firmly grasp the door at the top sides. This is critical. SLIDE RANGE INTO POSITION • Approach the range with the door angled in a vertical position. • Guide the hinges into the slots.
Installation STEP 8 ASSEMBLE AND ADJUST BURNERS Assemble burners as shown. Checkto be sure that burner heads and caps are securely seated. Pin(s) must completely engage holes to ensure proper assembly. (__ _- Burner Cap BurnerHead ._ • Check for proper ignition: - Push in one control knob and turn 90° to LITE (Brass) position. _ LocatorPins_ - The igniter will spark and the burner will light; the igniter will cease sparking when the burner is lit.
Installation FINALIZE INSTALLATION Place the burner grates over the burners. Press corner of the grate to the cooktop. The grates should be seated and should not rock. The grill and griddle are secured with screws atthe front. They are designed to be stationary and should not be removed. INSTALLATION The griddle has two leveling screws beneath the rear flue cover that can be used to adjust to the desired slope. The center screw is for shipping purposes only and can be removed.
Installation INSTALL 9" or 12" HIGH BACKSPLASH Slotsfor Vertical \ Adjustment \ Backsection • Install and level the range or cooktop according to the installation instructions, • Remove the backsplash packaging, Select the back, wall mount panel with mounting screw slots. l/B'L • Mark a horizontal line on the wall, 1/8" above the range/cooktop backguard, Bach • Use wood screws or fasteners (not supplied) to secure the back section to the wall.
NOTE:While performing installations described in this book, safety glasses or goggles should be worn. F<>rMonog'ra_? '_local s_r_Jice h_ )our arm, call l._S00. 444. l,_4 _. NOTE:]) ro(hi(:l sl)(_(if](:alions Pub.No.49-80222-1 PartNo. 164D4290P374 iml)l-o'_(m( m-(_ sul;_j(:(t ill i'_ a (:olHilitling to (:hmig( Wil[lotlr (_ll(l(_a'_'()r _/t noti(:(. Monogram: 17681Rev.
