Installation Instructions If you have questions, call 800-GE-CARES or visit our website at: www.monogram.
Installation Instructions BEFORE YOU BEGIN CAUTION: Read these instructions completely and carefully. THESE RANGES SHOULD BE INSTALLED IN CONJUNCTION WITH A SUITABLE OVERHEAD VENT HOOD. Due to the high heat capacity of this unit, particular attention should be paid to the hood and duct work installation to assure it meets local building codes. • IMPORTANT – Save these instructions for local inspector’s use. • IMPORTANT – Observe all governing codes • • • • • • MISE EN GARDE : and ordinances.
Design Information Installation Instructions Step 1, Remove Packaging ..............................................8 Step 2, Level the Range ....................................................9 Step 3, Install Anti-Tip Device ..................................9, 10 Step 4, Connect Range to Gas ......................................11 Step 5, Connect Electrical ..............................................12 Step 6, Slide Range into Position ................................12 Step 7, Replace Oven Doors ..
Design Information PRODUCT DIMENSIONS AND CLEARANCES 36" Wide Range Models 48" Wide Range Models 22" Optiona sh l Backspla 22" Backs Optional 12" plash 1-1/2" 12" 1-1/2" 35-1/4"-36-3/4" 35-1/4"-36-3/4" 47-7/8" 28-1/4" 28-1/4" 35-7/8" 48" and 36" Range Models 29-1/16" 12" Min. to Combustibles or 0" Min. to Combustibles with 12" or 22" Backsplash 36" Min. to Combustibles 9-1/2" 3/4" 22" High Backsplash with Shelf 22" 36" Min.
Design Information PRODUCT DIMENSIONS AND CLEARANCES 30" Wide Range Models 22" Ba Optional cksplash 27-3/8" 9-1/2" 3/4" 22" High Backsplash with Shelf 9" 22" 36" Min. to Combustibles 1-1/2" 9" 9" High Backsplash 35-1/4"-36-3/4" 0" Clearance 26-3/4" 29-7/8" 26-3/4" 29-1/4" 43-7/8" NOTE: Refer to Vent Hood Installation Instructions for hood height above the range. 30" Wide Range Hood Or 36" Wide Range Hood Or 48" Wide Range Hood 18" Min.
Design Information ADVANCE PLANNING TOOLS REQUIRED Refer to “Dimensions and Clearances” for appropriate placement and necessary clearances when planning the installation. • Saw • Measuring tape • Carpenter’s square • Pipe wrench • Large flat-blade screwdriver • Safety glasses • Drill and appropriate bits • Cabinetry can not be installed directly above the range. • We recommend the installation of a vent hood above the surface. – The vent hood must be at least 24" deep.
Installation Preparation POWER SUPPLY LOCATIONS If the electrical service provided does not meet the above specifications, it is recommended that a licensed electrician install an approved outlet. Gas Supply: • The natural gas models are designed to operate at 5" water column pressure. A regulator is required at the natural gas source to provide a maximum of 7" water pressure to the cooktop regulator. • Locate the electric supply as illustrated.
Installation STEP 1 REMOVE PACKAGING Slot Before moving the range indoors: • Remove outer carton and packing material from the shipping base. Hinge lock Pull the hinge locks down to unlock. Remove oven doors: • Fully open the door. • Each hinge has a hinge lock. Close the hinge latch down against the door frame. • Firmly grasp the door at the top sides. Kick Panel • Close the door to the near-vertical position. • Remove the kick panel by removing 2 screws at the top and pulling forward.
Installation STEP 2 LEVEL THE RANGE NOTE: Rear range leveling legs are not accessible after installation. • Adjust the height of the range to countertop height or higher. • Check to be sure the adjoining cabinets/countertops are level, front to back and left to right across the opening of the range. IMPORTANT: The range should always be installed at countertop height or higher. DO NOT INSTALL THE RANGE LOWER THAN ADJACENT COUNTERTOP HEIGHT.
Installation STEP 3 INSTALL ANTI-TIP DEVICE (CONTINUED) Small Hole For Wood (2) Wood Screws into Installations (2 Total) Back Wall (All Installations) (2) Large Holes For Concrete Installations Back Wall Small Holes For Wood Installations (2 Total) Wood Slide Strip f ide O iR ght S nge o r Ra Wall Dimension A A= Models 1/2" 5/8" 1/4" ZDP48 ZDP36 ZDP30 Dimension A Wood Construction: Concrete or Cement Construction: • Place the bracket against the back wall, into the right rear corner of the ins
Installation STEP 4 CONNECT RANGE TO GAS Assure that gas supply is turned off at the shut-off valve: CAUTION: • Connect flexible metal connector to incoming gas line pipe stub located on the left side on the bottom back of the range. MISE EN GARDE : Do not use a flame to check for gas leaks. Il ne faut pas utiliser de flamme pour vérifier s'il y a des fruites. • Turn on gas and check for leaks: – Use a liquid leak detector at all joints and connections in the system.
Installation STEP 5 CONNECT ELECTRICAL STEP 7 REPLACE OVEN DOOR(S) Plug power cord into properly grounded receptacle. IMPORTANT: Do not lift the door by the handle. To replace the oven doors: • Firmly grasp the door at the top sides. This is critical. • Approach the range with the door angled in a vertical position. • Guide the hinges into the slots. • Push the door in firmly while opening. • Once in position, open the door completely. Push the hinge locks back in and towards the front frame.
Installation STEP 8 ASSEMBLE AND ADJUST BURNERS Assemble burners as shown. Check to be sure that burner heads and caps are securely seated. Pin(s) must completely engage holes to ensure proper assembly. Burner Cap Burner Head (Brass) • Check for proper ignition: – Push in one control knob and turn 90° to LITE position. – The igniter will spark and the burner will light; the igniter will cease sparking when the burner is lit. – First test may require some time, while air is flushed out of the gas line.
Installation FINALIZE INSTALLATION Place the burner grates over the burners. Press corner of the grate to the cooktop. The grates should be seated and should not rock. The grill and griddle are secured with screws at the front. They are designed to be stationary and should not be removed. The griddle has two leveling screws beneath the rear flue cover that can be used to adjust to the desired slope. The center screw is for shipping purposes only and can be removed.
Installation INSTALL 9” or 12” HIGH BACKSPLASH • Install and level the range or cooktop according to the installation instructions. • Remove the backsplash packaging. Select the back, wall mount panel with mounting screw slots. • Mark a horizontal line on the wall, 1/8" above the range/cooktop backguard. • Use wood screws or fasteners (not supplied) to secure the back section to the wall.
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Pub. No. 49-80222-1 Part No. 164D4290P374 17681 Rev.
