GE Monogram Installation Instructions Professional Ranges 48" Natural Gas Models ZDP48N4G ZDP48N6R ZDP48N6D 48" LP Gas Models ZDP48L4G ZDP48L6R ZDP48L6D 36" Natural Gas Models ZDP36N6 ZDP36N4R ZDP36N4D 36" LP Gas Models ZDP36L6 ZDP36L4R ZDP36L4D 30" Natural Gas Modal ZDP3ON4 30" LP Gas Modal ZDP30L4 ®
Before you begin--Read these instructions completely and carefully. IMPORTANT: Save these instructions for local inspector's use. IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer. NOTE TO CONSUMER: Keep these instructions reference. F!l,,,t:s,,u_,:_l This appliance must be properly grounded. See "Electric For Monogram local service in your area, 1-800-444-1845. For Monogram Service in Canada, Call 1-888-880-3030.
Design Information Pr@ssional Models" Available These ranges are factory set fbr either natural gas or liquid propane gas. Order the model for your installation situation.
Design Information Pr@ssional Ranges Product Dimensions 1/4" & Clearances ii Optionalt 35-1/4"-30-3/4" 48" Wide Range Models 36"Wide RangeModels _29-1/16" 3-1/4" q_i 12"_ _ 21-1/4" High Shelf 30" Min.
Design Information Pro/essional Ranges Product _27-3/8" Dimensions & Clearances" -_ 21-1/4" _High 36" Min. to Combustibles Shelf LowBack 35-I/4"-36-8/4" -- o" Clearance i i 26-8/4" , _ 9-7/B" \ r_q r_q --26-3/4'm --29-1/4" 43-7/8" 30" Wide Range Models Note: Refer to Vent Hoed Installation Instructions for / Or 36" WideRangeHood hood height above the range.
Design Information Pr@ssional Advance Planning Refer to "Dimensions and Clearances" for appropriate placement and necessary clearances when planning the installation. • Cabinetry can not be installed directly above the range. • We recommend the installation of a vent hood above the surface. -The vent hood must be at least 24" deep. -The vent hood must be the same width as the range. -For 48" models, we recommend hood blower be 1200 CFM. • Allow 36" min.
Installation Preparation Pro/essional Pozogr Supply Locations Gas Supply: • The natural gas models are designed to operate at 6" to 14" water column pressure. • The liquid propane models are designed to operate at 11 to 14" water column pressure. A regulator is required at the L.R source to provide a maximum of 14" water pressure to the range regulator.
Installation Pro/essional Ranges DoorHingeRoller Before moving the range indoors: • Remove outer carton and packing from the shipping base. material (Closed} Remove _/ • Open KickPanel • Remove the kick panel by removing at the top and pulling forward. range To simplify handling of the range: • Remove the grates knobs. back. and to reduce and drawers • Remove grill and griddle ATTEMPT TO REMOVE GRIDDLE Remove bolts and fully and hold down. and the out of" the frame.
Installation Pr@ssional Ranges 36" and 48" Wide Models: Pu¢_ilove Packaging (continued) Level the Range • Remove the panel from the rear of the shipping pack. Lay the panel on the floor directly in front of the installation location. The range should be placed on this panel to prevent damage to the floor. All Models: • Remove the two strips fi'om the oven interior: Place the strips on the floor at lef} and right sides of the installation location.
Installation Pro/essional Ranges Small HoleForWood (2}Wood Screwsinto Installations(2Total) BackWall (All Installations) (2)LargeHolesFor \ ConcreteInstallations Install Sack Wall Small HolesForWood installations(2 Total)\ Anti-Tip Device (continued) Wood J Slide __ Strip Dimension A=dels[V'o 112" ZDP48 A 5/8" ZDP36 1/4" ZDP30 \Dimension A Wood Construction: Concrete • Place the bracket against the back wall, into the right rear corner of the installation location.
Installation Pro/essional A manual shut-offvalve it will be accessible. must be installed where Ranges Flexor RigidGas gul_ Assure that gas is turned off at the shut-off valve. Connect • Remove all burner/hanger screws. • Lift and remove all open top burners/hangers to reveal the gas inlet location at the back of the range. • Pull the flexible metal gas line through the back of the range and into the cooking area until it meets the regular.
Installation Pro/essional Plug power receptacle. cord into properly Ranges grounded Connect Electrical st° 7 Slide the Range Into Position Replace • Carefully, slide the range into position. -Be careful not to entange power cord and gas flexible tubing. • Be sure the right rear leg is engaged in the slot of the installed anti-tip bracket. • Check for proper installation by grasping the range at the top fi'ont edge and carefully attempt to tilt the range forward.
Installation Pr@ssional 9 Assemble & Adjust Burners • Replace the burner bowls and burner caps. • Adjustments should not be required, unless vibration during transit or variations in local gas supply make minor adjustments necessary. Burner- Ranges _,__M Igniter ain Burner ", CAUTION: Burner adjustments must be made by a qualified technician at the time of installation. Extreme care should be used if adjustments are made after installation.
Notes Pro[essional Ranges 14
Notes Pro[essional Ranges 15
NOTE: While perfolming installations describedin this book, safety glasses or gogglesshould beworn Q Monogram: General Electric Company Louisville, KY40225 NOTE: Pioduct E]ect_i_ The_ _u6}eet implovement _t<>] e, mate_ t_ _:hange without is a colltlltIlilt,_ _aI_, a}_pearal_:e no_i,e endeax and ol at Ge_lel sl_e_ itleati_ fls aJ e a] Pub.No.49_8814-4 ] Dwg.No. 164D3333P058J (N.
