INSTALLATION INSTRUCTIONS with Design Guide Wine Chiller, Wine Reserve and Beverage Center Monogram.
Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT – Save these instructions for local inspector’s use. Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. • Note to Consumer – Keep these instructions with your Owner’s Manual for future reference. If you received a damaged refrigerator, you should immediately contact your dealer or builder.
Consignes de Sécurité AVERTISSEMENT Risque d’explosion. Conservez les matériaux et vapeurs inflammables tels que l’essence à l’écart de votre réfrigérateur. Le non-respect de cette instruction peut entraîner un risque d’incendie, d’explosion ou de décès. AVERTISSEMENT 3RXU UpGXLUH OH ULVTXH G¶pWRXႇHPHQW SHQGDQW O¶LQVWDOODWLRQ GH FH SURGXLW QH SDV ODLVVHU OHV petites pièces à la portée des enfants âgés de moins de 3 ans. BRANCHEMENTS ÉLECTRIQUES AVERTISSEMENT Risque d’électrocution.
Design Guide CONTENTS Important Information .............................................2, 3 Design Guide Tools Required ..............................................................4 Parts Supplied ...............................................................4 Staining Wood Drawer Fronts ......................................4 Installing Custom Frame Panel ....................................4 The Installation Space ............................................. 5 Product Clearances ...................
Design Guide THE INSTALLATION SPACE Flush Installation Dim. A Filler panel or cleat to be set back even with front of case. CABINET Front edge of product case CABINET 110° Front face 120° NOTE: Handle and handle VWDQGRႇ GHSWK LV *For a standard installation of Custom-Framed unit: The product must be installed so that the front face will project 2" forward of adjacent cabinets. This position will allow a full door swing and prevent interference with adjacent cabinetry.
Design Guide PRODUCT CLEARANCES The stainless steel wine chiller, wine reserve and beverage center is factory set for a 110° door swing. Models that accept custom panels have a 95° door swing. When installed in a corner: • Allow 4" min. clearance on the hinge side for the 90° door swing and to allow racks to slide out. • Allow 10" minimum clearance on the hinge side for a full 110° door swing. (Models ZDWI240WII and ZDBI240WII have a 95° door swing.
Installation Instructions STEP 1 REMOVE PACKAGING • Remove corner blocks and foam drawer stops. • Remove all packing material, tape and protective plastic coverings. • Remove stainless steel toekick taped to the back of the unit. WARNING Small objects are a choke hazard for children. Remove and discard any parts not used. AVERTISSEMENT Les petits objets peuvent étrangler les enfants. Il faut jeter toutes les pièces qui ne sont pas utilisées.
Installation Instructions STEP 2 REVERSE DOOR SWING (Cont.) Install Toekick The toekick has a cutout on the left and right sides. Remove the plug on the left side and reinstall on the right side. If you choose to install the stainless steel toekick, reinstall the plug on the right side of that toekick. • Install original screws and spacers or screws and spacers supplied with the stainless steel toekick. Install screws through the spacer VWDQGRႇ WRHNLFN DQG LQWR the base as shown.
Installation Instructions CUSTOM FRAME PANEL MODELS Model ZDWI240WII and ZDBI240WII These models require a custom panel frame surrounding the glass. There are two options: the panel may be 29 Ǝ RU Ǝ KLJK $ Ǝ SDQHO UHTXLUHV D QRWFK FXW LQWR WKH bottom of the panel to avoid interference with the hinges. • Rout the back side of the panel to the dimensions shown. • A custom handle of your choice or ZTBSS1 Tubular Handle must be installed before the panel is mounted onto the door.
Notes 10 31-46122-6
Notes 31-46122-6 11
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. NOTE: Product improvement is a continuing endeavor at Monogram. Therefore, materials, appearance and specifications are subject to change without notice. 31-46122-6 02-19 GEA Monogram.
