Owner Manual

10 49-80513-4
Before you
call for
service
Troubleshooting Tips
Chimney Hood
Problem Possible Causes What To Do
Fan fails to circulate
air or moves air
slower than normal
&KHFNWREHVXUHWKHPHWDOJUHDVH¿OWHUDQG
WKHFKDUFRDO¿OWHULISUHVHQWDUHFOHDQ&OHDQ
WKHPHWDOJUHDVH¿OWHUVHHWKH0HWDOJUHDVH
¿OWHUVHFWLRQDQGLIWKHKRRGLVUHFLUFXODWHG
(not vented to the outside), replace the
FKDUFRDO¿OWHUVHHWKH&KDUFRDO¿OWHU
VHFWLRQ,IFOHDQLQJDQGUHSODFLQJWKH¿OWHUV
does not correct the problem, call for service.
6XႈFLHQWPDNHXSUHSODFHPHQW
air is required for exhausting
appliances to operate to rating.
Check with local building codes, which may
require or strongly advise the use of makeup
air. Visit Monogram.com for available
makeup air solutions.
)DQNHHSVJRLQJRႇ
and on
The motor is probably
RYHUKHDWLQJDQGWXUQLQJLWVHOIRႇ
This can be harmful to the motor.
&KHFNWREHVXUHWKH¿OWHULVFOHDQDQGFKHFN
GXFWZRUNIRUEORFNDJH,IRႇDQGRQF\FOLQJ
continues, call for service.
Lights will not work
and rings around the
operating buttons
DUHÀDVKLQJ
Light(s) were replaced with
bulbs with greater than the 120
volt, 50 watt limit.
Replace with the correct type and size bulb.
See the Light bulbs section.
Light will not stay on
high setting
Use 120 volt, 50 watt, MR16 halogen bulbs
with a GU10 base and make sure they
are inserted securely. It is important to
replace with bulbs that do not exceed the
recommended wattage. Higher wattage bulbs
will cause the outer rings to blink, and the
lights will not function at the highest levels.
See the Light bulbs section.
The hood controls
are not operating
correctly
Disconnect power to the hood by turning the
FLUFXLWEUHDNHURႇRUE\UHPRYLQJWKHIXVHLQ
the home fuse box. Wait 30 seconds to allow
the hood controls to reset and then replace
the fuse or move the circuit breaker back on.
Sequential presses
of the light or fan
buttons will change
the setting from the
lowest setting to
RႇWRWKHKLJKHVW
setting, or from the
KLJKHVWVHWWLQJWRRႇ
to the lowest setting
So that you can easily set the
controls to the desired setting,
the hood is designed for the light
and fan buttons to cycle through
the settings.
This is normal
When pressing the
0HPRU\2ႇEXWWRQ
to turn on the light,
the fan comes on
instead
For your convenience, it is
normal for the lights and fan
to remember their last setting
ZKHQ\RXSUHVVWKH0HPRU\2ႇ
button.
If you want only the lights on, press the “FAN
´RUWKH³)$1±´EXWWRQWRWXUQWKHIDQRႇ
When you power the hood up next time, only
the lights will function. NOTE: You may turn
WKHIDQDQGOLJKWVRႇRURQVHSDUDWHO\XVLQJ
the “+” or “–” buttons.