Specification Sheet

For questions about your
appliance, please call 1-800-626-2000.
Product Specication Created 10/19PAGE 3 OF 4
HELPFUL TIPS
FRONT VIEW SIDE VIEW
W
24" (61.0)
2 1/4"
(5.7)
4 7/8"
(12.4)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5)
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISP480DXSS
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
Top Case Trim
3/4"
Min.
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
FRONT VIEW SIDE VIEW
W
24" (61.0)
2 1/4"
(5.7)
4 7/8"
(12.4)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5)
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISP480DXSS
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
Top Case Trim
3/4"
Min.
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
A
B
D
C
e refrigerator will project forward, slightly beyond adjacent cabinetry.
A
Mounting the junction box in this location
will also allow for front accessibility
through access panel.
B
Water supply area.
WARNING:
e refrigerator is top heavy and must be
secured to prevent the possibility of tipping
forward. Failure to do so may result in death
or serious injury.
e information below is for cabinet design
only. When installing the anti-tip system you
must use the product installation instructions.
Determine your installation construction and
required anti-tip configuration.
C
Installed Under Soffit
After installing unit into installation
opening, raise grille panel and screw
metal case sides to adjacent cabinet. When
installed under a soffit, the soffit cannot
exceed 24" deep. e top case trim overlaps
the bottom of the soffit.
D
Wooden Wall Studs and No Soffit
• Cut a 2" x 4" block and secure to
brackets provided.
• Secure brackets to back wall of opening
at 84" or your installation height from
the floor.
E
Metal Wall Studs and No Soffit
is method requires securely fastened
cabinets on both sides and a 3/4" minimum
wood brace above unit, with it’s front
surface 24" from back wall.
• After installing unit into opening, raise grille
panel and attach metal case top trim to 3/4"
minimum wood brace.
• e brace spanning the enclosure must be
securely fastened to cabinets on both sides.
See Installation Instructions for detailed
instructions.
STANDARD INSTALLATION
ANTI-TIP BRACKET
E