Environmental monitoring
Wireless Sensor: Low Cost, Reliable And Ready to Use Big Features in a Small Package! Wireless Sensor Features • FCC/CE Certified Wireless Radio Technology High-Gain, Flexible, Robust, Whip Antenna (250 - 350 ft range)* Long-life Coin Cell Battery (Get +300k Radio Transmissions) • Operating Frequencies (25 Channels) 900 MHz (North America, South America and New Zealand) 868 MHz (Europe, Middle East and Africa) Uncluttered 900 MHz Operating Frequency Robust, Flame Retardant ABS Plastic Housing 433 MHz
PolarXpress Link Ethernet Gateway General Description The PolarXpress Link Ethernet gateway allows your PolarXpress X Wireless Sensors to communicate with the PolarXpress Online Wireless Sensor Monitoring and Notification System without the need for a PC. Simply plug this device into any open network port with internet connection and it will automatically connect with our servers. This is the perfect solution for locations where there is an active internet connection.
POLARXPRESS ETHERNET GATEWAY SPECIFICATIONS Ethernet Ethernet Types: Antenna: Hardware: IEEE Standard Compliance: Operation: Cross-Over Correction: Addressing: Host Address: Default Port: Protocols Supported: Cable Connector: Memory Capacity: Power Power Supply: Standard, POE Connector: SMA Gain (dBi):5.0 10/100 Ethernet Controller 802.3-2002 Full and Half-Duplex Automatic MDI/MDI-X Pre-programmed MAC Address 3000 UDP, DHCP, TCP Cat 5 40,000 messages 5.5 V AC adapter or 5.
PolarXpress Link USB Gateway General Description The PolarXpress Link USB Gateway allows your PolarXpress X Wireless Sensors to communicate with PolarXpress Online Wireless Sensor Monitoring and Notification System. Simply install the USB driver and plug the device into an available USB port on a Microsoft Windows PC. If the PC has an active internet connection and you wish to use it with the PolarXpress online software, install the PolarXpress Gateway application to pass sensor data to the online system.
POLARXPRESS USB GATEWAY SPECIFICATIONS USB Type: Display Name: Display Type: Version: Software Compatible Platforms: Bus Reported Device Description: Memory Capacity: Power Maximum Power Required: USB 2.0 Full Speed Bus Standard Wireless Sensor Gateway Status 1.0.3.0 Microsoft Windows XP, Vista, Windows 7 M+ LINK 40,000 messages Powered through USB output of PC 50 mA Mechanical Enclosure Dimensions Weight ABS plastic 1.75 x 0.71 x 0.40 inches 0.
PolarXpress Link Cellular Gateway General Description Don’t have an existing network connection where you need it most? The PolarXpress Cellular Gateway allows your PolarXpress Wireless Sensors to communicate with the PolarXpress Online Wireless Sensor Monitoring and Notification System via cellular transmission. This is the perfect solution for remote locations, or where an existing internet connection is not an option.
POLARXPRESS CELLULAR GATEWAY SPECIFICATIONS Cellular CDMA Antenna Dual Band CDMA Frequency Range: 800 / 1900 MHz Connector: SMA Gain (dBi): 1.5 Power Input Power 5.5 VDC @ 900 mA Mechanical LEDs Enclosure Dimensions Weight Cellular Status LED, Online Status LED, Sensor Network Status LED ABS 5.004 x 3.8 x 1.51 in. 7 ounces Environmental Operating Temperature Storage Temperature -30 to +70ºC -40ºC to +85ºC 1.51 in. Managing What Matters V 1.
PolarXpress Link Sensor Router General Description PolarXpress Routers allow you to extend the coverage area (range) of your wireless sensor network by repeating the signals between your wireless sensors and the wireless gateway. General Description On power up, the router will locate a gateway that has the “best” wireless signal available. The router then auto-configures itself to communicate and link with this gateway.
POLARXPRESS Sensor router SPECIFICATIONS Power Standard Operating Range Max Operating Range Input Frequency Max Power Consumption 100-240 VAC 90-264 VAC 50/60Hz +/- 3Hz 1.
PolarXpress XH Sensor High Accuracy Wireless Humidity (RH) Sensor General Description The High Accuracy (HA) Wireless Humidity (RH) Sensor allows you to accurately monitor the relative humidity of the air within a room or enclosure. It also can record and chart the temperature value. Features • Measures relative humidity with high accuracy. • Measures temperature in Celsius and Fahrenheit.
Technical Specifications Supply Voltage Current Consumption Operating Temperature Range (Board Circuitry and Battery) Optimal Battery Temperature Range (Coin Cell) Accuracy RH Operating Range RH Response Time 2.0 - 3.6 VDC* 0.7 µA (sleep mode) 2 mA (radio idle/off mode) 2 mA (measurement mode) 25 mA (radio RX mode) 35 mA (radio TX mode) -20ºC to +60ºC (-4ºF to +140ºF)** +10ºC to +50ºC (+50ºF to +122ºF) +/- 2% under normal conditions (10% - 90% RH) 0 - 100% RH 8 sec (tau 63%) ± 10 ± 3.0 ±8 ± 2.5 ± 2.
PolarXpress XT Sensor Wireless Temperature Sensor General Description The RF Wireless Temperature Sensor uses a type NTC thermistor to measure temperature. Features • Accurate to ± 1º C (± 1.8º F) • Increased accuracy by user calibration to ± 0.25º C (± 0.45º F) • PolarXpress online wireless sensor monitoring and notification system to configure sensors, view data and set alerts via SMS text and email.
Technical Specifications Supply Voltage Current Consumption Operating Temperature Range (Board Circuitry and Battery) Optimal Battery Temperature Range (Thermistor Only) Thermistor Temperature Range (Leaded Thermistor) X2 Sensor Only Accuracy @ 25ºC User Calibrated Accuracy Time Constant @ 25ºC 2.0 - 3.6 VDC* 0.
PolarXpress XW Sensor Wireless Water Sensor General Description The Wireless Water Sensor detects the presence or nonpresence of water. Features • 3 ft. leaded wires. • Immediately detects water. • PolarXpress online wireless sensor monitoring and notification system to configure sensors, view data and set alerts via SMS text and email. Principle of Operation The PolarXpress Wireless Water Sensor detects when water is present by completing the circuit between the two leaded wires.
Technical Specifications Supply Voltage Current Consumption Operating Temperature Range (Board Circuitry and Battery) Optimal Battery Temperature Range (Coin Cell) Lead Wire Length Detection Wires 2.0 - 3.6 VDC* 0.7 µA (sleep mode) 2 mA (radio idle/off mode) 2 mA (measurement mode) 25 mA (radio RX mode) 35 mA (radio TX mode) -20ºC to +60ºC (-4ºF to +140ºF)** +10ºC to +50ºC (+50ºF to +122ºF) 3 ft. (36 in.) High Impedance * Hardware can not withstand negative voltage.
PolarXpress XM Sensor Wireless Infrared Motion Sensor General Description The Wireless Motion Sensor uses an infrared sensor to accurately detect movements made by people/animals within 16.4 ft (5 m) range. Features • Detect motion. • PolarXpress online wireless sensor monitoring and notification system to configure sensors, view data and set alerts via SMS text and email. Principle of Operation The PolarXpress Wireless Infrared Motion Sensor detects motion and movement using infrared technology.
Technical Specifications Supply Voltage Current Consumption Operating Temperature Range (Board Circuitry and Battery) Optimal Battery Temperature Range (Coin Cell) Sensor Detection Range Reted Consumption Current (Standby) Sensor Warm-up Time 2.0 - 3.6 VDC* 0.7 µA (sleep mode) 2 mA (radio idle/off mode) 2 mA (measurement mode) 25 mA (radio RX mode) 35 mA (radio TX mode) -20ºC to +60ºC (-4ºF to +140ºF)** +10ºC to +50ºC (+50ºF to +122ºF) 16.
PolarXpress XC Sensor Wireless 0-1 mA Current Sensor General Description The Wireless 0-1mA DC Current Sensor is designed to work with current transducers that convert a measured AC current signal to a DC signal up to 1mA. When a current transformer (CT) is used to obtain the measured AC signal, and connected to a current transducer, the Wireless 0-1mA DC Current Sensor will provide a signal that is proportional to the measured AC current that can be displayed. Features • Measures current up to 1 mA DC.
Technical Specifications Supply Voltage Current Consumption Operating Temperature Range (Board Circuitry and Coin Cell) Optimal Battery Temperature Range (Coin Cell) Sensor Resolution 0-1 mA Input 0-5 Amp Input 200 Amp CT Input Conversion Time Full Scale Current Input Resistance 2.0 - 3.6 VDC* 0.
PolarXpress XL Sensor Wireless Light Sensor General Description The Wireless Light Sensor detects the presence of light. Features • Detects presence of light. • PolarXpress online wireless sensor monitoring and notification system to configure sensors, view data and set alerts via SMS text and email. Principle of Operation The Wireless Light Sensor uses a photo resistor to detect the presence of light around the device.
Technical Specifications Supply Voltage Current Consumption 2.0 - 3.6 VDC* 0.7 µA (sleep mode) 2 mA (radio idle/off mode) 2 mA (measurement mode) 25 mA (radio RX mode) 35 mA (radio TX mode) -7ºC to +60ºC (-4ºF to +140ºF)** +10ºC to +50ºC (+50ºF to +122ºF) ᶲ = ± 50º 0 - 1,000 Lux Operating Temperature Range (Board Circuitry and Battery) Optimal Battery Temperature Range (Coin Cell) Angle of Half Sensitivity Max Light Level 20019 10° 20° 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.
PolarXpress XO Sensor Wireless Open/Closed Sensor General Description The Wireless Open/Closed Sensor can be used to detect when a door or window is opened and closed using a magnetic switch. Features • Detects when a door or window is accessed. • Magnet is included. • PolarXpress online wireless sensor monitoring and notification system to configure sensors, view data and set alerts via SMS text and email.
Technical Specifications - ELECTRONICS Supply Voltage (Battery Power) Current Consumption Operating Temperature Range (Board Circuitry and Battery) Optimal Battery Temperature Range (Coin Cell) 2.0 - 3.6 VDC* 0.7 µA (sleep mode) 2 mA (radio idle/off mode) 2 mA (measurement mode) 25 mA (radio RX mode) 35 mA (radio TX mode) -20ºC to +60ºC (-4ºF to +140ºF)** +10ºC to +50ºC (+50ºF to +122ºF) * Hardware can not withstand negative voltage. Please take care when connecting a power device.
