Specifications

ManualsBrandsMonitor ManualsDomestic AppliancesM2200

SECTION

K

PROTECTIVE FEATURES

LOSS

OF

POWER-AUTOMATIC RESET:

NOTEilf

power

to the

heater

is

interrupted,

a

thud-like

noise

may be

heard

in the

combustion chamber.

This

is

normal,

and

should

not

cause alarm.

For

power interruptions

of up to 30

minutes,

the

set

memory

is

kept

and

will resume operation

automatically

with

the set

memory.

For

power interruptions beyond

30

minutes, your

heater

will

resume operation

(after

a 3

minutes

cool

down period)

in the

MANUAL mode

and

maintain room temperature according

to the

previous

setting temperature you've selected

in

case

of

manual operation before power

interruption,

the

initial

setting temperature (60°F)

in

case

of

automatic operation before power

interruption.

When

the

heater resume operation,

The

Display

Window

will

show 88:88 indicating

the

need

to

reset

the

clock

and the day of the

week

for

automatic

operation.

CHILD

LOCK:

NOTE:The

CHILD LOCK

will

help

to

prevent accidental

operation

as

well

as

small children

from

altering

controls.

To

operate

the

CHILD LOCK simply hold

the

"CHILD

LOCK"

Button

down

for 3

seconds,

or

until

you

hear

two

short beeps.

The

function

is

activated

immediately

and the

"CHILD LOCK" Light will illuminate.

To

deactivate

the

CHILD LOCK

simply

hold

the

"CHILD

LOCK" Button down

for 3

seconds,

or

until

you

hear

two

short beeps.

The

"CHILD LOCK"

Light

will

go

out.

The

lock

can be

deactivated

at any

time

in

this way.

During normal operation

the

CHILD

LOCK

may be

activated

and all controls

other

than

the OFF

switch

will

be

locked.

Deactivating

the

lock

releases

the

controls.

If

the

lock

is

activated while

the

heater

is

turned OFF, then

all

functions will

be

locked.

If the

heater

is

Turned

OFF

while

the

CHILD

LOCK

is

activated,

it

cannot

be

turned

ON

again

until

the

lock

is

deactivated.

OVERHEAT PREVENTION

If

your

heater

overheats,

a

thermostatic

switch

will

automatically

stop

the

flow

of

kerosene

and

extinguish

the

flame.

The

Display Window shows

"E

14".

Restore heater

operation

by

following

the

steps below

NOTE:Other

symptoms listed

in the

trouble shooting chart

may

cause

the

display

window

to

show

"E

14",

besides

an

overheat situation.

Step

1:

Turn

the

Heater

Off

Press

the

Operation

Button

to put it in the

"Off"

position.

Step

2:

Allow

the

Heater

to

Cool

Wait

approximately

30 to 45

minutes

for the

heater

to

cool

completely.

Step

3:

Unplug

the

Heater from

the

Wall Outlet.

Step

4:

Remove Obstructions

The

overheated

condition

may be

caused

by

obstructions

blocking

the air

flow

to the

heater

.

Check:

•

The

front

of the

heater

•

The

circulation

fan (on the

back

of the

heater).

•

The

flue

pipe

(outside)

Step

5:Remove

the

Front Cover Assy

Remove

the

screws

at the

Front Cover Assy,

and

carefully

remove

the

Front Cover Assy.

Remove

any

accumulation

of

dust

or

other

matter

that

may

be

covering

the

burn

chamber

and the

heat

exchangers

inside

the

heater.

Step 6:Replace

the

Front

Cover Assy

Step

7:

Plug

in the

Heater

Step

8:

Re-program

the

Heater

Step

9:

Turn Heater

On

/i\

CAUTION:

If the

unit overheats

a

second time, turn

it off and

contact your

MPI

dealer

for

service.

ELECTRICAL

FUSE

In

the

unlikely

event

of a

failure

in the

heater's

electrical

system,

a

fuse

will

"blow"

and

interrupt

the

power.

Do not

attempt

to

change

the

fuse.

Contact

your

MPI

dealer

for the

name

of a

trained

and

certified

service

representative

in

your

area.

NO

TE:

Using

a

surge protector

can

minimize

the

chances

of

a

blown fuse caused

by

power surges.

24