owners manual
Contents Introduction: 1 Amp Panel & Controls 2 Positioning/Initial Set Up 4 Set Up 4 Specification 5 Trouble Shooting 6 Warranty 7 Owner Information 7 Introduction: The Bronze Series has been intricately engineered to optimise your audio experience, whether you’re listening to your favourite album or watching the latest Hollywood blockbuster.
Amp Panel & Controls 3 4 5 6 7 8 2 9 1 10 10a 11 1. RCA Stereo Inputs (Left & Right) This is the method of signal input when using a stereo amplifier system, connection can be provided by a pair of high-quality signal cables from the pre-out section of an amplifier. The crossover frequency will need to be set if using this method of connection. If using the Bronze Series speakers set the crossover dial to approximately 80Hz. This may vary depending on room and tastes.
user guide.) When the subwoofer is correctly set-up, you should not be able to identify its location easily in the room. 6. Bass Switch This switch tailors the bass response of the subwoofer to your tastes. There are three settings: Music, Movies and Impact. Movie mode provides a relatively flat response down to 35Hz. Music mode is -2dB down on Movie mode but goes lower, all the way down to 30Hz. Impact mode is +3dB up on Movie mode and comfortably goes down to 40Hz. 7.
Positioning/Initial Set Up Leave the subwoofer unplugged from the mains until the installation procedure is completed. The subwoofer should be sited in the most suitable position, preferably not directly in the corner of a room as this may cause excessive bass boom. Once a desirable position is achieved it is important to check if the cables are long enough to reach comfortably without being under tension.
Specification Bronze W10 Subwoofer System Format Long-throw 10” driver featuring ‘dished’ C-CAM cone. 10” flat panel ABR (auxiliary bass radiator). 18 mm M.D.F.
Trouble Shooting Should you experience any technical, or set-up problems with your subwoofer please check the Trouble Shooting guide below: My subwoofer will not turn on/ no power. • Is the LED illuminated on the top of the unit? If not, check your mains lead is properly connected both at the subwoofer and at the mains outlet. Also check the fuse of the amplifier and mains plug (where fitted). • Is the LED red? If so, you have power going to the unit.
Warranty Both the craftsmanship and the performance of this product is covered by the manufacturer’s warranty against manufacturing defects provided that the product was supplied by an authorised Monitor Audio retailer under the consumer sale agreement. For the period of cover please refer to the product page on our website: monitoraudio.com for the product you have purchased. When purchasing Monitor Audio products, please keep your receipt of purchase safe, as this validates your warranty.
Monitor Audio Ltd. 24 Brook Road Rayleigh, Essex SS6 7XJ England Tel: +44 (0)1268 740580 Email: info@monitoraudio.com Web: monitoraudio.com Designed & Engineered in the United Kingdom Made In China Version 1.
Loudspeaker x2 Subwoofer 5mm (Exc. Centre) UK/ Euro Quick Start Guide Bronze 200 & 500 Only x8 3mm x8 x8 x8 monitoraudio.
Wiring Feet (Bronze 200 & 500) 1 - + + - + +
Loudspeaker Positioning 2 Channel Stereo Surround Sound AV xm xm -22° xm 0° 22° -30° 30° A A 90° 90° -110° 110° -90° 135° -150° B 7.1 = A + B 5.
AV Subwoofer 2 Channel AVR Sub Out Pre Amp Out
Power Manual Subwoofer & Speakers monitoraudio.
EN Frequency Response Sensitivity (1W@1M) Nominal Impedance Maximum SPL (Pair) Power Handling R.M.S Recommended Amp Requirements R.M.
EN Low Frequency Limit Upper Frequency Limit Amplifier Output Bass EQ Modes Input Impedance Mains Input Voltage (Factory Preset) Power Consumption Dimensions (Including grille, amp & feet) (H x W x D) Product Weight FR Limite de fréquence basse Limite de fréquence haute Sortie de l'amplificateur Modes d'égalisation de la basse Impédance en entrée Tension d'entrée principale (Préréglage d'usine) Consommation électrique Dimensions (grille, amplificateur et pied compris) (H x L x P) Poids du
© Monitor Audio Version 2 2020 Monitor Audio Ltd 24 Brook Road Rayleigh, Essex United Kingdom SS6 7XJ +44 1268 740 580 info@monitoraudio.com monitoraudio.
ENGLISH WARNING • TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE • TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE • TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE PLUG TO WIDE SLOT AND FULLY INSERT.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus with water. 6. Clean only with a dry cloth. Great care and attention has gone into the materials chosen to produce the product. A gentle wipe with a dry, clean cloth is all that is required to remove any dust. Treat it as you would a fine piece of furniture because that is how they have been designed. 7.
Guarantee and Service Correct Disposal of Waste Electrical and Electronic Equipment (WEEE) by User in Private Households in the EU. To help us find your warranty details within our customer database, should the need arise, please take a few minutes to register your product(s) online at: monitoraudio.com. This symbol on the product or accessories indicates that they must not be disposed of with your household wastes throughout the EU.
Claims under this Guarantee The equipment should be returned in its original packaging to the original supplier where possible, or to any other authorised Monitor Audio dealer. If it is not possible to return the equipment by hand, then it should be sent carriage prepaid via a reputable carrier. If the original packing is not available replacement packaging can be purchased from Monitor Audio.
We, Monitor Audio Ltd. (Manufacturer and Importer) 24 Brook Road Rayleigh Essex SS6 7XJ England ENGLISH EC Declaration of Conformity EN6100-3-3: 01.95 Electro magnetic compatibility (EMC) – Part 3: Limits – Section 3: Limits of voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current up and including 16 Ampere per phase. Signed by: 16 Name: D.S.