Vented Gas Log Set Models: VWF18, VWF24, VWF30, VWF36 WARNINGS Installation and Operating 277300 Instructions VWF log cover If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. – Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. – WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance.
VWF Series Vented Gas Log Set CONTENTS Thank you and congratulations on your purchase of a Vermont Castings Group Log Set. PLEASE READ THE INSTALLATION AND OPERATION INSTRUCTIONS BEFORE USING THE APPLIANCE! IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty. Important Safety Information .................................... 3 Product Specifications ........................
IMPORTANT SAFETY INFORMATION OWNER Please leave these instructions with the appliance. Please retain these instructions for future reference. WARNING Read these instructions carefully before installing or trying to operate this vent-free gas heater. This product must be installed by a licensed plumber of gas fitter when installed within the Commonwealth of Massachusetts. • Any change to this heater or its controls can be dangerous.
Product specifications VWF Series Vented Gas Log Set Model VWF18N VWF18P VWF24N VWF24P VWF30N VWF30P VWF36N VWF36P Fuel Natural LP Natural LP Natural LP Natural LP Control Manual Manual Manual Manual Manual Manual Manual Manual Nominal BTU/h 60,000 60,000 70,000 60,000 80,000 60,000 80,000 60,000 WARNING Gas Specifications GAS pressures Natural Propane (LP) 4.0” w.c. 10.0” w.c. 10.0” w.c. 13.0” w.c. 4.0" w.c. 10.0" w.c. Manifold Pressure Max. Gas Inlet Pressure Min.
GETTING STARTED Check your packing list to verify that all listed parts have been received.
VWF Series Vented Gas Log Set Placement in a fireplace with a restrictive barrier Important information for the installation of this gas log set The following are guidelines for placing a VWF log set in a fireplace that has a restrictive barrier along the bottom front opening of the fireplace. Some examples of barriers are glass/screen door frames and sunken/recessed fireplaces.
INSTALLATION VWF Series Vented Gas Log Set Install and operate the appliance as directed in this manual. Damper stop installation A damper stop must be provided with the unit. The damper stop must be installed as shown in Figure 3 to prevent full closure of the fireplace damper blade and provide a minimum flue opening, according to the table on Page 5.
INSTALLATION VWF Series Vented Gas Log Set Covers must be installed prior to operation to prevent overheating. NOTICE WARNING INSTALL VALVE COVER Grate bar must not touch the valve.
VWF Series Vented Gas Log Set Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing WARNING WARNING WIRING - MILLIVOLT Do not connect to 110 Volt supply Millivolt Control Valve Pilot LG1044 The Millivolt (thermopile) is a self powered combination gas control that does not require 110V AC to operate.
CONNECT THE GAS CAUTION NOTICE: A qualified gas appliance installer must connect the appliance to the gas supply. Consult all local codes before installation. WARNING NOTICE VWF Series Vented Gas Log Set Connecting directly to an unregulated propane/ LPG tank can cause an explosion. Use new black iron pipe, steel pipe, copper tubing, or internally tinned copper tubing. Copper or internally tinned copper tubing can only according to the National Fuel Gas Code, section 2.6.
CONNECT THE GAS VWF Series Vented Gas Log Set The gas log set gas inlet connection is 3/8" NPT at the regulator, inlet on the right side facing the gas log. If a left side connection is required, the connecting pipe may be led under the rear of the gas logs or behind the grate for connection to the inlet. Test all gas joints from the gas meter to the appliance regulator for leaks using a gas analyzer or soap and water solution after completing connection. DO NOT USE AN OPEN FLAME.
LOG PLACEMENT VWF Series Vented Gas Log Set filling THE burner pan Fill the burner pan with vermiculite to the bottom of the rear log and sloped to the front edge of the burner pan. Excess vermiculite can spill forward or to the side of the burner pan. Do not overfill the propane model. Do not cover the pilot (if SPK or MVVK is installed) with vermiculite or rock wool (embers). VWF18 massive oak logs 1. Slide shield plate behind burner pan. Figure 11 2.
LOG PLACEMENT VWF Series Vented Gas Log Set Front Right Log #3 3. Place front left log #2 on the front of the grate and to the left. Figure 13 4. Place front right log #3 on the front of the grate and to the right. Figure 13 NOTE: Allow 2" between the back log and the two front logs. Front Left Log #2 LG839 Figure 13 Place Front Left and Right Logs on Grate Left Side Middle Log #4 Right Side Middle Log #5 LG839 VWF18MO front logs 5. Place left side middle log #4 as shown. Figure 14 6.
LOG PLACEMENT VWF Series Vented Gas Log Set VWF24 massive oak logs Shield Plate 1. Slide shield plate behind burner pan. Figure 16 2. Center rear log #1 on grate bars and flush with rear of the grate. Figure 17 Rear Log #1 Burner Pan Figure 16 Slide Shield Plate Behind Burner Pan Figure 17 Center Rear Log on Grate Bars LG842 LG830 VWF24 shield Front Left Log #2 LG830 Front Right Log #3 LG842 3. Place front left log #2 on the front of the VWF24MO rearleft. logFigure 18 grate and to the 4.
LOG PLACEMENT Left Side Middle Log #4 VWF Series Vented Gas Log Set Right Side Middle Log #5 6. Place right side middle log #5 as shown. Figure 20 7. Place left top log #7 as shown. Figure 20 Right Top Log #6 Figure 20 Place Right Side Middle Log and Left Top Log LG844 LG844 VWF24MO middle logs 8. Place right top log #6 as shown. Figure 21 Figure 21 Place Right Top Log VWF30 massive oak logs LG845 1. Slide shield plate down back of burner pan. Figure 22 2.
LOG PLACEMENT VWF Series Vented Gas Log Set Front Left Log #2 Front Right Log #3 3. Place front left log #2 on the front of the grate and to the left. Figure 24 4. Place front right log #3 on the front of the grate and to the right. Figure 24 NOTE: Allow 2" between the back log and the two front logs. Right Middle Log #5 Left Middle Log #4 LG848 Figure 24 Place Front Logs LG848 5. Place VWF30MO left middle log #4 logs as shown. front Figure 25 6. Place right middle log #5 as shown.
LOG PLACEMENT VWF Series Vented Gas Log Set VWF36 massive oak logs Shield Plate 1. Slide shield plate behind burner pan. Figure 28 Burner Pan LG852 Figure 28 Slide Shield Plate Behind Burner Pan Rear Log #1 Lg852 2. Center rear log #1shield on VWF30 grate bars and flush with rear of the grate. Figure 29 plate LG853 Figure 29 Center Rear Log on Grate LG853 VWF30MO rear log Right Front Log #4 Left Front Log #2 3. Place front left log #2 in front of the plate and to the left.
LOG PLACEMENT VWF Series Vented Gas Log Set 6. Install left side log #6. Figure 31 7. Install right side middle log #7. Figure 33 8. Install right side log #10. Figure 31 Top Left Middle Log #8 Right Side Middle Log #7 Left Side Log #6 Right Side Log #10 LG855 Figure 31 Place Left & Right Side Logs and Right Side Middle Logs LG855 9. VWF30MO Install topmiddle left logs middle log #8.
LOG PLACEMENT VWF Series Vented Gas Log Set Rear Log #1 VWF18 American oak logs NOTE: Each log has an identifying number embossed on bottom surface. 1. Place Back Log #2 on grate bars on back of grate. Figure 35 Front Log #1 Figure 35 Place Rear Log on Grate Bars LG859 LG859 2. Place Front Log #1 on front of grate. VWF18AO rear log Figure 36 LG860 Figure 36 Place Front Log Right/Left Middle Log #4 Right/Left Middle Log #4 LG860 3.
LOG PLACEMENT VWF Series Vented Gas Log Set VWF24 American oak logs Rear Log #1 NOTE: Each log has an identifying number embossed on bottom surface. 1. Place Back Log #2 on grate bars on back of grate. Figure 39 Front Log #2 Figure 39 Place Back Log on Grate LG863 LG863 rear log 2. Place Front LogVWF24AO #1 on front of grate. Figure 40 Figure 40 Place Front Log on Grate LG864 Right/Left Log #4 Right Log #3 LG864 3. Position Right Log #3 on top VWF24AO front right of Log #1 log and Log #2.
LOG PLACEMENT VWF Series Vented Gas Log Set VWF30 American oak logs Rear Log #2 NOTE: Each log has an identifying number embossed on bottom surface. 1. Place Back Log #2 on grate bars on back of grate. Figure 43 LG867 Figure 43 Place Rear Log on Grate Front Log #1 LG867 VWF30AO rear log 2. Place Front Log #1 on front of grate. Figure 44 LG868 Figure 44 Place Front Log LG868 front log 3.
LOG PLACEMENT VWF Series Vented Gas Log Set Left Crossover Log #7 7. Place Left Crossover Log #7 on Log #2 and Log #5. Figure 47 Right Crossover Log #8 Figure 47 Place Left Crossover Log #7 LG871 LG871 left cross logLog #8 8.VWF30AO Place Right Crossover on Log #3 and Log #7.
LOG PLACEMENT VWF Series Vented Gas Log Set models VWF24B (6 Logs) Top Left Log #6 Figure 49 1. Slide shield plate behind burner pan. 2. Place Back Log #1 on grate bars on back of grate. 3. Place Middle Log #2 in front of Log #1. 4. Position Right Front Log #3 on right front side of grate. 5. Position Left Front Log #4 on left front side of grate. Make sure notch in bottom of log sits on grate prong. 6. Rest Top Right Log #5 across top right sides of Log #1 and Log #2. 7.
LOG PLACEMENT VWF Series Vented Gas Log Set models VWF24/18 split river oak 1. Slide shield plate behind burner pan. Figure 51 Shield Plate Burner Pan Rear Log #1 Figure 51 Slide Shield Plate Behind Burner Pan LG837 LG837 2. Place Rear Log #1 on back of grate. Figure 52VWF18 shield plate LG875 Bottom Right Log #3 1st Grate Prong 2nd Grate Prong Figure 52 Place Rear Log 4th Grate Prong 3rd Grate Prong 3. Place Front Left Log #2 in front of back log on left arm of grate.
LOG PLACEMENT VWF Series Vented Gas Log Set Bottom Front Left Log #5 5. Rest Bottom Left Log #5 on back log #1 and to the outside of the first grate prong. Figure 54 6. Rest right end of Top Right Log #4 on bottom right log. Figure 54 LG877 Top Right Log #4 Figure 54 Place Bottom Front Left and Top Right Logs Top Center Log #7 LG877 2418 SRO logs 5 4 7. Place end of Top Left Log #6 on bottom left log. Rest the other end between the first and second grate prongs. Figure 55 8.
LOG PLACEMENT VWF Series Vented Gas Log Set models VWF30/24 split river oak Shield Plate 1. Slide shield plate behind burner pan. Figure 56 Burner Pan Figure 56 Slide Shield Plate Behind Burner Pan LG830 Rear Log #1 LG830 VWF24 shield First Grate Prong Fifth Grate Prong 2. Place Back Log #1 on back of grate. Figure 57 LG879 Second Grate Prong Bottom Right Log #3 Fourth Grate Prong Third Grate Prong Figure 57 Place Rear Log 3.
LOG PLACEMENT VWF Series Vented Gas Log Set Bottom Front Left Log #5 5. Rest right end of Top Right Log #4 on bottom right log. Figure 59 6. Rest Bottom Left Log #5 on back log #1 and to the outside of the left grate prong. Figure 59 Top Right Log #4 LG881 Figure 59 Place Top Right and Bottom Front Left Logs Top Center Log #7 LG881 3024SRO bot frt top right logs 7. Place end of Top Left Log #6 on bottom left log. Rest the other end between the first and second grate prongs. Figure 60 8.
LOG PLACEMENT VWF Series Vented Gas Log Set models VWF36/30 split river oak Shield Plate 1. Slide shield plate behind burner pan. Figure 61 Burner Pan Figure 61 Slide Shield Plate Behind Burner Pan Rear Log #1 LG852 Lg852 VWF30 shield plate First Grate Prong 2. Place Back Log #1 on back of grate. Figure 62 Sixth Grate Prong LG883 Second Grate Prong Third Grate Prong Figure 62 Place Rear Log Fifth Grate Prong Fourth Grate Prong Bottom Right Log #3 LG883 3630SRO rear log 3.
LOG PLACEMENT VWF Series Vented Gas Log Set Bottom Front Left Log #5 5. Rest right end of Top Right Log #4 on bottom right log. Figure 64 6. Rest Bottom Left Log #5 on back log #1 and to the outside of the left grate prong. Figure 64 Top Right Log #4 Figure 64 Place Top Right Log and Bottom Front Left Log LG885 LG885 3630SRO Logs 4&5 7. Place end of Top Left Log #6 on bottom left log. Rest the other end between the first and second grate prongs. Figure 65 8.
LOG PLACEMENT VWF Series Vented Gas Log Set models VWF18 split Pine Shield Plate 1. Slide shield plate behind burner pan. Figure 66 Burner Pan Figure 66 Slide Shield Plate Behind Burner Pan Right Front Log #1b LG837 Left Front Log #1a LG837 2. Place Left Front Log #1a on front left of grate. Figure 67 VWF18 shield plate 3. Place Right Front Log #1b on front right of the grate. Figure 67 LG887 Figure 67 Place Front Logs Side Support Log #2 LG887 VWF18 SP front logs 4.
LOG PLACEMENT VWF Series Vented Gas Log Set Rear Log #3 5. Fit cutout in the bottom left of Rear Log #3 over the back end of log #1a. Rest right end of Log #3 on rear grate bar. Figure 69 Right Log #4 LG889 Figure 69 Place Rear Log LG889 VWF18SP rear log 6. Rest front end of Right Log #4 on right top of Log #1b. The back end of Log #4 rests to right hump on Log #3. Figure 70 Right Middle Log #5 Figure 70 Place Right Log LG890 LG890 7.
LOG PLACEMENT VWF Series Vented Gas Log Set Top Center Log #7 8. Lay Top Center Log #7 across log #5 with back end resting on Log #3. Figure 72 LG892 Figure 72 Place Top Center Log LG892 VWF18SP Top ctr log Top Left Log #8 9. Place front end of Top Left Log #8 on Log #1a. Let back end of Log #8 rest on Log #7.
LOG PLACEMENT VWF Series Vented Gas Log Set models VWF24 split Pine Shield Plate 1. Slide shield plate behind burner pan. Figure 74 Burner Pan Right Front Log #1b Left Front Log #1a Figure 74 Slide Shield Plate Behind Burner Pan LG830 2. Place left front log #1a on front left of grate. Figure 75 3. Place LG830 right front log #1b on front right of the grate. Figure 75 VWF24 shield LG831 Figure 75 Place Front Logs Side Support Log #2 LG831 4.
LOG PLACEMENT VWF Series Vented Gas Log Set Right Log #4 6. Rest front end of right log #4 on right top of log #1b. The back end of log #4 rests to right hump on log #3. Figure 78 Figure 78 Place Right Log LG834 Right Middle Log #5 Left Log #6 LG834 7. Place front of right middle log #5 on VWF24 right log top right of log #1b. Rest back end of log #5 on top right of log #4. Figure 79 8. Rest front end of left log #6 on log #1a and back end of log #6 just left of middle log #1.
LOG PLACEMENT VWF Series Vented Gas Log Set models VWF30 split Pine 1. Slide shield plate behind burner pan. Figure 82 Shield Plate Burner Pan Figure 82 Slide Shield Plate Behind Burner Pan Right Front Log #1b Left Front Log #1a LG821 LG821 2. Place left front log #1a on front left of plate grate.shield Figure 83 3. Place right front log #1b on front right of the grate. Figure 83 LG822 Figure 83 Place Front Logs Side Support Log #2 4.
LOG PLACEMENT VWF Series Vented Gas Log Set Left Log #6 Right Log #4 6. Rest front end of right log #4 on right top of log #1b. The back end of log #4 rests to right hump on log #3. Figure 86 7. Rest front of left log #6 just left of the middle of log #1a and back end of log #6 just left of middle of log #3. Figure 86 Right Middle Log #5 LG825 Figure 86 Place Left and Right Logs 8. Place front of right middle log #5 on top right of log #1a. Rest back end of log #5 on top right LG825 of log #4.
LOG PLACEMENT VWF Series Vented Gas Log Set Model VWF24/18WP Weathered PINE LOG Shield Plate 1. Slide shield plate behind burner pan. Figure 90 Burner Pan Figure 90 Slide Shield Plate Behind Burner Pan Rear Log #1 LG837 LG837 VWF18 shield plate Rear Stand of Grate Figure 91 Place Rear Log LG894 VWF2418WP rear log 2. Place Rear Log #1 on back of grate. Left side should fit on grate in front of rear stand. Right side goes on the rear stand of grate.
LOG PLACEMENT VWF Series Vented Gas Log Set Top Left Log #5 Top Right Log #4 5. Place Top Right Log #4 on Bottom Right Log #2 resting on grate. Figure 93 6. Place Top Left Log #5 behind Rear Log #1 on the notch on rear left of grate stand. Figure 93 7. Place Mid Front Log #6 on grate between center and middle left grate bars. Fit notch on back of log on the cross grate bar.
LOG PLACEMENT VWF Series Vented Gas Log Set Model VWF30/24WP Weathered PINE Shield Plate LOG 1. Slide shield plate behind burner pan. Figure 94 Burner Pan Rear Log #1 Figure 95 Slide Shield Plate Behind Burner Pan LG830 2. Place Rear Log #1 on back of grate. LG830 Left side should fit on grate in front VWF24 of rear stand.shield Right side goes on the rear stand of grate. Figure 95 LG897 Figure 96 Place Rear Log LG897 3024WP rear log Bottom Right Log #2 3.
LOG PLACEMENT VWF Series Vented Gas Log Set Top Right Log #4 Bottom Left Log #3 4. Place Top Right Log #4 on Bottom Right Log #2 resting on grate. Figure 97 5. Place Bottom Left Log #3 on grate. The “V” of the log should straddle the end grate bar. Figure 97 LG899 'V' Straddling Grate Bar Figure 97 Place Bottom Left and Top Right Logs LG899 3024WP logs 3 & 4 6. Place Top Left Log #5 behind rear log #1 on the notch on rear left of grate stand. Figure 98 7.
LOG PLACEMENT VWF Series Vented Gas Log Set Model VWF36/30WP Weathered PINE LOG Shield Plate 1. Slide shield plate behind burner pan. Figure 99 Burner Pan LG830 Figure 99 Slide Shield Plate Behind Burner Pan Rear Log LG830 VWF24 shield 2. Place Rear Log #1 on back of grate. Left side should fit on grate in front of rear stand. Right side goes on the rear stand of grate. Figure 100 Figure 100 Place Rear Log LG901 Bottom Right Log #2 Bottom Left Log #3 LG901 3630WP back log 3.
LOG PLACEMENT VWF Series Vented Gas Log Set Top Left Log #5 5. Place Top Right Log #4 on Bottom Right Log #2 resting on grate. Figure 102 6. Place Top Left Log #5 behind Rear Log #1 on the notch on rear left of grate stand. Figure 102 Top Right Log #4 LG903 Figure 102 Place Top Left and Right Logs Top Center Log #7 LG903 3630WP top logs 7. Place Mid Front Log #6 on grate between center and middle left grate bars. Fit notch on back of log on the cross grate bar. Figure 103 8.
OPERATING INSTRUCTIONS for spk AND CVTHL kits VWF Series Vented Gas Log Set safety INSTRUCTION FOR MANUAL CONTROL (SPK) FOR YOUR SAFETY READ BEFORE LIGHTING WARNING A. BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS: • Do not attempt to light any appliance.
operating instructions for MVVK Kits VWF Series Vented Gas Log Set Millivolt CONTROL LIGHTING INSTRUCTIONS STOP! Read the safety information label. Make sure the manual shutoff valve is fully open. Turn gas control knob clockwise to the “OFF” position, and turn ON/OFF switch to “OFF” position. Wait (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! 5. From “OFF” position, turn the gas control knob counterclockwise to “PILOT” position.
flame appearance VWF Series Vented Gas Log Set Checking Burner flames Flame should be yellow and extend vertically (not curling toward fireplace screen). Ember bed should have a yellow/orange glow LG909 Figure 104 Flame Appearance LG909 VWF30 Flame appearance PILOT FLAME APPEARANCE Thermocouple/ Thermopile Tip The pilot flame must always be present when appliance is operating. It should just touch the top of the thermocouple/ thermopile tip.
VWF Series Vented Gas Log Set fireplace draft test IMPORTANT: Fireplace Draft Test During Initial Installation It is critical to verify that your chimney is drafting properly because the fireplace and gas logs function as a system. WARNING Although Vermont Castings Group goes to great lengths to design vented gas log sets that minimize sooting, all vented log sets will soot over time. Sooting normally appears as areas of black powder-like substance on the logs.
cleaning and servicing VWF Series Vented Gas Log Set remote control receiver replacement WARNING The remote control receiver and batteries are very sensitive to heat. Exposure to high temperatures can cause the receiver to malfunction and shorten the life of the batteries.
REPLACEMENT PARTS VWF Series Vented Gas Log Set 1 2 3 4 5 8 6 Ref. 1. 2. 3. 4. 5. 6. 7. 7. 48 Description Injector Manual Control Valve Millivolt Control Valve Manual Shaft Extender Control Knob Regulator Switch Pilot 7 Qty.
REPLACEMENT PARTS VWF Series Vented Gas Log Set 4 2 6 1 8 5 7 3 MASSIVE OAK LOGS Ref. 1. 2. 3. 4. 5. 6. 7. 8. Description Back Log Left Front Log Right Front Log Left Side Middle Log Right Side Middle Log Right Top Log Left Top Log Top Crossover Log Qty.
REPLACEMENT PARTS VWF Series Vented Gas Log Set AMERICAN OAK LOGS 1 Ref. 1. 2. 3. 4. 5. 6. 7. 7. 8. 2 4 6 3 Description Front Log Back Log Right Middle Log Left Middle Log Top Right Log Top Left Log Top Center Log Top Center Log Top Top Center Log Qty. 1 1 1 2 2 1 1 2 1 VWF18AO 27D8576 27D8577 -27D8580 ---27D8578 -- VWF24AO 27D8584 27D8585 27D8588 27D8580 -27D8587 ---- VWF30AO 27D8592 27D8593 -27D8580 27D8594 -27D8578 -27D8600 8 7 3 5 BIRCH LOGS Ref. 1. 2. 3. 4. 5. 6. Description Qty.
REPLACEMENT PARTS VWF Series Vented Gas Log Set 8 8 7 9 7 6 6 5 5 4 4 2 2 3 1a 3 1a 1b 1b SPLIT PINE LOGS Ref. 1a. 1b. 2. 3. 4. 5. 6. 7. 8. 9. Description Front Left Log Right Front Log Side Support Log Rear Log Right Log Right Middle Log Left Log Top Center Log Top Left Log Top Top Left Log 27D8520 Qty.
REPLACEMENT PARTS VWF Series Vented Gas Log Set 1 2 WEATHERED PINE LOGS Ref. 1. 2. 3. 4. 5. 6. Description Rear Log Bottom Right Log Bottom Left Log Top Right Log Top Left Log Mid Front Log Qty. 1 1 1 1 1 1 VWF24/18WP 27D5140 27D5141 27D5142 27D5143 27D5144 27D5145 3 4 6 5 1 WEATHERED PINE LOGS Ref. 1. 2. 3. 4. 5. 6. 7. Description Rear Log Bottom Right Log Bottom Left Log Top Right Log Top Left Log Mid Front Log Top Center Log Qty.
VWF Series Vented Gas Log Set 27D8520 53
Massachusetts Residents Only — Please read and follow these special requirements 2. Approved Carbon Monoxide Detectors. Each carbon NOTE REGARDING VENTED PRODUCTS This product must be installed by a licensed plumber or gas fitter monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 when installed within the Commonwealth of Massachusetts. Any residence with a direct vent product must have a CO listed and IAS certified. 3. Signage.
LIMITED LIFETIME WARRANTY POLICY Lifetime Warranty The following components are warranted for life to the original owner, subject to proof of purchase: Firebox, Combustion Chamber, Heat Exchanger, Grate, Stainless Steel Burners, and Vented Fiber Ceramic and Refractory Logs. Five Year Warranty The following components are warranted for 5 years to the original owner, subject of proof of purchase: Aluminized Burners.
Vermont Castings Group 149 Cleveland Drive • Paris, Kentucky 40361 www.vermontcastingsgroup.