Installation Condition 1.Refer to the {Standard Part List} when unpacking , check all parts available . 2.Do not disassemble mixer body by yourself. 3.Connect inlet hoses to supply valves. 4 Make sure inlet pipes and supply valves have been installed and cleaned, also ensure no impurities in pipeline. 5.After installation, check all joints for leakages. 6.Suggest don't fit the faucet in the severely corrosive environments.
Sing Basin Faucet Part List EL Description Nos 1 Body of mixer 1 Bass installation part. 1 3 Flexible hoses 2 4 Fixing nuts 1 5 Use’'s manual 1 & Gloves 2 step 2 Please make sure there is a hole with Put the mixers body with flexible hoses © a5mm~admm{¢ 1 3/8"1 5/16” jon onto the sink through the hols, then the sink. Then dismantles the fixing nuts assemble the fixing nuts to the tap from from the mixer, and put on the gasket to the bottom. the base installation parts.
Sing Basin Faucet Installation step 3 stop 4 Fasten the fixing nuts by spanner, and Connect the two Flexible hoses to the tighten the cross screws on the fixing angle valves . Referring to the red and RUS bY Cross Screwdriver. blue point signals on the handle, please connect them to hot water naive and oid water valve accordingly. step 5 Hot ~_ «Cod 1. Operating handle gradually is better for valve protection. 2. Lift handle will turn on faucet the wider the tilting angle.
Three Hole Basin Faucet Installation step 1 waterfall fixed base Consent Brass @) with waterfall Body 4) and put the Brass Part (through the basin hole Install Faucet Bud Gaskets and Mounting Not in sequence and tighten th nut with 2 wrench. Then pul Tee Gasket 5 step 2 Handle -Medieval seat Decorate seat the bate sing $ control water body Remove the Decorate Seats (9 and put thee on the basin holes.
Three Hole Basin Faucet Installation step 3 Connect one side of tie inlet Hoses & to the Control Water Bodies the thee side to Tee @, and tighten them. The red hose is for hot water and the blue hose is for cold water.
Wall Mount Bathtub Faucet Part List SIN Description 1 Faucet Body 2 S-Linton 3 | Decoration cover 4 Hand shower 5 Shower hose 6 User's manual 7 loves 2 Wall Mount Bathtub Faucet installation step 1 FIGURE. ei 51 Le cold winter connector S-colonial | step 2 ‘After wrapping hie tape, connect the S union tithe water toilet connector. (The distance between the hot water outlet and cold water outlet connector is 150mm, the height apart from floor should be fixed according ta the bathtub height).
Wall Mount Bathtub Faucet Installation step 3 step 4 Tr Then mount the shower hose to the mixer and hand shower, The above installation instruction is also applicable te the shower mixer's installation step 5 1. Opan water naive to sack if theta is any leakage 2 When turning the handle upward, the valve is apen. And the turning angle can control water outflow. tha user can tum it to the left or right to regulate the water temperature. 3.
Bathtub Faucet Installation step 1 waterfall lix ad base Connect Brass Parts () with Faucet Body (0 and put the Brass Part @ through the hole.
Bathtub Faucet Installation snot? slop 2 Install Hot and Cold Hoses & as the above drawings. Connect one side of Hot and Cold Hoses B with Transforms Control Valve @, the other aids to Conceal Water Bodies Left is to hot water, right Is to cold water. One side of Shower Hose #5 is connected to Hand Shawear®, the other side is connected to the Shaker Connect Hose 08 through Hand Pedestal @ Then the other side of Shower Connect Hose @ is connected to Transforms Control Valve 40.
Bathtub Faucet Application Instruction 4: The middle one of the Handles § is control water diversion of the Faucet Body 1 and Hand Shower 5. Turn left, water comes out from the Hand Shower 8:turn right water comes cut from the Faucet Body 1. exasperating handle gradually is better fo valve protection. 3: The handles 9 tum right or lef is to pane or close, The larger the rotation angle. the larger the flow rate.
Care and Maintenance In order to keep the mixer surface bright, please clean the mixer regularly. Rinse faucet with clean water and wipe with soft cotton cloth. Avoid suing cleaning powder, harsh cleaning chemicals, brushes.and cloth with coarse surface to prevent scratching and corrosion. Do not use acid cleaner lo clean the faucet as it may cause surface corrosion of the faucet. if the faucet comes into contact with harmful acid substances, please rinse it with water immediately.
