Owner's manual

To charge the Battery Pack:
1. Make sure the Strobe is off or remove the Battery Pack from the Strobe.
2. Plug the recharger cable into the battery recharger socket on the Battery Pack (see Figure
2 for location).
3. Plug the recharger into an AC mains wall outlet.
NOTE: When using the Universal recharger, make sure the correct adapter plug
is inserted into the recharger before plugging the recharger into the wall
outlet.
CAUTION: Use of rechargers other than the one supplied (PSC-2U) may damage
the stroboscope and void the warranty.
The battery module contains circuitry to control the charge. The amber LED blinks steady to
indicate that the battery is being charged. The LED will turn solid amber as it nears complete
charge. Once the charge is completed, the LED turns solid green and the recharger will trickle
charge the battery. The Battery Pack may be used at this point.
NOTE: The total charge time is typically about 4-5 hours. The Battery Pack may be left on
trickle charge indefinitely.
The LED also indicates that charging has stopped due to a problem. The LED will blink 5, 6,
7, or 8 short red blinks and then one long green blink to indicate the following: 5 = over voltage,
6 = over current, 7 = too hot, and 8 = too cold.
7.3 Battery Disposal
Prior to disposing of the Battery Pack, the user must remove the Nickel Metal Hydride batteries.
To do this, remove the four screws on the under side of the Battery Pack and separate the case
halves, exposing the battery. Remove the cables from the battery and place tape over the
battery terminals to prevent them from shorting. The battery should be sent to a recycling
center or returned to the factory. The rest of the parts may now be disposed of.
E-10S-1
1.0 ESPECIFICACIONES
El Modo Interno:
La Gama Rápida 100 - 12,500 FPM (Destella por Minuto)
Certeza Rápida de Tasa El más grande de FPM ±0.5 o ±0.01% de lectura
Resolución Rápida de Tasa 0.1 FPM
El Despliegue actualize la Tasa Continuo
El Modo Externo/Tacómetro:
La Gama rápida y Demuestra 5.0 a 12,500 FPM - Externos y mismo que internas a 0 son aceptables
Medidas de Tacómetro 5 a 250,000 RPM - Ningún destello
Certeza El más grande de FPM ±0.1 o ±0.01% de lectura
El despliegue Actualiza la Tasa 1 segundo típico
El disparador para Destellar la Demora < 5 µsec
Entrada externa 0 a 5 volt TTL Compatible (pk 12V max)
1 anchura de pulso de min de µsec, La orilla Positiva provocó
Base de Tiempo Oscilador Fijo de Cristal
Despliegue Despliegue alfanumérica de 6 dígitos de VCL, backlit con 0.3 pulgada {7.62 mm}
los dígitos altos
Indicadores Indicación Baja de Batería, En el Indicador del Objetivo, Cerrada En, Modo
Externo, Modo Tacómetro, ÷2 ×2
Ajuste Un cuatro Botón del Afinador del Cuadrante con la década selecciona para la tasa
rápida arriba o hacia abajo, multiplique por 2 y divida por 2
Memoria Guarda ocho tasas rápidas programables y dura la tasa rápida en apaga
Pulso de Salida 350 µsec pulso positivo, 5 Vdc típico
Poder Movible 6 Vdc Paquete Recargable de Batería con Control Integrante de Carga de
Electrónica para rechargers (PSC-2 or PSC-2U Recharger: 9 Vdc @ 500mA)
Poder Ligero 150 mJ/Destello hasta 3000 FPM
Duración Rápida 10 - 30 microsegundos típico
Corra Tiempo 2 horas típicas en 1800 FPM y más de 1 hora en 6000 FPM con baterías cargadas
Cargue Tiempo aproximadamente 4 horas
Peso 1.2 lbs {544 g} inclusive Paquete de Batería
La Figura 1 Las dimensiones en Pulgadas [mm]