User manual

13
English
The IR remote control for the player is sup-
plied with a battery. Prior to initial operation,
remove the protective film from the battery
holder. When pressing a button, always direct
the remote control to the infrared sensor(21) of
the player. There must be no obstacles between
the sensor and the remote control.
If the remote control is not used for a longer
time, remove the battery as a precaution so that
the remote control will not be damaged in case
the battery should leak.
Replacing the battery:
Push the latch of the battery holder to the right
(arrow 1 in the figure below) and remove the
holder (arrow 2). Remove the old battery and
insert the new battery (3 V button cell, type
CR 2025) into the holder with the positive pole
pointing upwards. Push the holder back into the
remote control.
Batteries must not be placed in the
household waste. Always take them
to a special waste disposal (e. g. collec-
tion container at your retailer).
To switch the player on /off, use the POWER
button(20).
Inserting a replay medium:
– Insert a CD with the lettering showing up-
wards into the CD slot (A) until it is retracted
automatically.
– Connect a USB storage medium (USB flash
drive or USB hard disk with separate power
supply) to the USB port (B).
– Insert a memory card (notched corner up-
ward and contacts to the right) into the slot
SD / SDHC (C) until it engages.
SD / SDHC
To remove the card, slightly push it into the
slot until it disengages.
To switch between the replay media, use
the button MODE (23). When a medium has
been read in, it will be replayed automatically.
If a USB storage medium or a memory card has
been selected and is then removed, the player
automatically switches over to the CD player
mechanism. The same happens when a new
CD is retracted.
Control options and information on the display
indications can be found in chapter3.1.
8 Specifications
Amplifier power
Rated power: � � � � � � � � � 120 W
Music power: � � � � � � � � � 170 W
Speakers: � � � � � � � � � � � � � 25 cm (10”) bass speaker
and 2�5 cm (1”) tweeter
Frequency range: � � � � � � � � 20 – 20 000 Hz
Input sensitivity: � � � � � � � � 6 mV (MIC 1 / 2),
300 mV (LINE /AUX IN)
Level LINE /AUX OUT: � � � � � 1 V
Connections
MIC 1: � � � � � � � � � � � � � � combined
XLRjack / 6�3 mm jack, bal�
MIC 2: � � � � � � � � � � � � � � 6�3 mm jack, bal�
LINE IN / OUT: � � � � � � � � � � RCA jacks
AUX IN / OUT: � � � � � � � � � � � 3�5 mm jacks
Tone control: � � � � � � � � � � ±10 dB / 100 Hz (BASS)
±10 dB /10 kHz (TREBLE)
Ambient temperature: � � � � 0 – 40 °C
Power supply:
Mains voltage: � � � � � � � � 230 V / 50 Hz
Power consumption: � � 170 VA
Battery operation: � � � � � � internal rechargeable
lead gel batteries
(2 × 12 V / 4�5 Ah)
Operating time: � � � � � � 4 – 6 hours approx�
Dimensions (W × H × D): � 360 × 580 × 320 mm
Weight: � � � � � � � � � � � � � � 19�2 kg
8.1 Wireless transmission
Range: � � � � � � � � � � � � � � � approx� 30 m
Transmitting power of
the transmitter module: � � � ≤ 10 mW (EIRP)
Radio frequencies
Channel Frequency Channel Frequency
01 863.1 MHz 09 863.2 MHz
02 864.1 MHz 10 864.2 MHz
03 863.6 MHz 11 863.7 MHz
04 864.6 MHz 12 864.7 MHz
05 863.3 MHz 13 863.4 MHz
06 864.3 MHz 14 864.4 MHz
07 863.8 MHz 15 863.9 MHz
08 864.8 MHz 16 864.9 MHz
Note concerning multichannel operation:
The number of channels to be used in parallel de-
pends on the conditions at the place of application
(e. g. on interference due to other wireless systems
or high-frequency sources such as fluorescent lamps).
In ideal conditions, up to four channels can be oper-
ated at the same time without mutual interference.
Two examples of a suitable channel selection for four
wireless transmission paths:
Example 1:
channel 01 – channel 03 – channel 06 – channel 12
Example 2:
channel 06 – channel 09 – channel 15 – channel 16
All rights reserved by MONACOR
®
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual
may be reproduced in any form or by any means for any commercial use.
Subject to technical modification.