Molift Mover 205 EN - User manual BM05101 Rev.
Molift Mover 205 / www.etac.com English Manual Content Important Molift Mover 205 ......................................2 Lifter components...................................2 About Molift Mover 205 .........................2 General .....................................................3 Declaration of conformity........................3 Conditions for Use ..................................3 Warranty ................................................3 Product identification ..............................
Molift Mover 205 / www.etac.com Molift Mover 205 Lifter components: Lifting arm Hand control Sling bar Push handles Lifting column Manual emergency lowering Battery Motor / actuator Electric emergency lowering Legs Emergency stop Chassis Wheel / castor (rear with break) About Molift Mover 205 Molift Mover 205 is a mobile lifter intended for lifting and transferring a person from/to bed, floor, chair, wheelchair or toilet with a sling.
Molift Mover 205 / www.etac.com General CE declaration The product, and its related accessories, described in this instruction for use (IFU), is in compliance with the regulation (EU) 2017/745 of 5. April 2017 – as a medical device, risk class I. The product has been tested and approved by a third party according to standards IEC 60601-1, IEC 60601-1-2 and EN/ISO 10535:2006.
Molift Mover 205 / www.etac.com Technical data Safe Working Load (SWL): Maximum A-weighted sound power level: 205 kg (452 lbs) LWA = 63,2 dB Weight of unit: Operating forces button: Excl. battery and sling bar: 35,5 kg/78,3 lbs Chassis: 18 kg/39,7 lbs Lifting column: 17,5 kg/38,6 lbs Battery: 1,6 kg/3,7 lbs 4-point medium sling bar: 2,5 kg/7,3 lbs Buttons on handset: 3.
Molift Mover 205 / www.etac.com Assembly Battery and hand control Charge the battery. The battery must not be in the battery holder during assembly! 1 2 3 Lifting column 1. Connect hand control to bottom of battery holder. 2. Insert battery. 3. Connect hand control wire to push handle so it does not fall to the floor when dropped. Checklist after assembly Place lifting column in chassis. Make sure that the red arrow on the lower part of the column corresponds with the edge of chassis.
Molift Mover 205 / www.etac.com How to use Molift Mover 205 General safety precautions Safe Working Load Only use accessories and slings that are adjusted to fit the user, type of disability, size, weight and type of transfer. The lifter is marked with Safe Working Load (SWL) The lowest SWL shall always be used if safe working load (SWL) differs between lifter, sling bar and body support unit Working pause ratio/Duty Cycle.
Molift Mover 205 / www.etac.com Safety devices Emergency stop / Emergency lowering Molift Mover 205 is equipped with several safety devices, which are intended to prevent damage or injuries to personnel and equipment in the case of incorrect use. Manual emergency lowering The lifter has an overload sensor preventing the lifter to be operated if the load exceeds SWL. Electrical emergency lowering The lifting arm is hinged to prevent the arm and sling bar from squeezing the user.
Molift Mover 205 / www.etac.com Electronics Transport and operating conditions Battery and service indicator Transport and storage The lifter has two indicator lights on the battery holder. For long time storage it is recommended that the emergency stop button is activated (pushed in). The lifter can be stored and transported under temperatures between -25 - 70 °C. Service indicator Battery indicator Operating The lifter is designed for use at standard room temperatures (+5 to +40°C).
Molift Mover 205 / www.etac.com Charging Battery indicator (LED) Battery charger Mains cable (disconnecting device) Battery Charger The battery charger can be used as a tabletop charger or mounted to a vertical wall surface close to a power outlet, minimum 120 cm above the floor. The charger has to be used outside the patient environment. The Charger must be placed or installed in a way that makes it easy to disconnect mains cable plug. Take care not to damage the cable.
Molift Mover 205 / www.etac.com Transfer Plan the lifting operation in advance to ensure that it is as safe and smooth as possible. Remember to work ergonomically. Assess the risks and take notes. The assistant is responsible for the safety of the user. Molift Mover 205 can be used with 4-point sling bar for different types of transfers; sitting, recumbent or ambulating. The sling bar’s hook design prevents sling to be inadvertently detached when mounted correct.
Molift Mover 205 / www.etac.com Transfer Lowering into sitting Try to position the user as low as possible (preferably resting the feet on the chassis) when transferring the lifter with a suspended user. In this way the centre of gravity will be low and reduce the risk of instability.
Molift Mover 205 / www.etac.com Accessories Recommended optional equipment and accessories for Molift Mover 205. with all Molift Mover 180 4-point sling bars. Sling bars and sling bars with scale Molift Mover 205 can be used with 2 or 4 point sling bar. Sling bars are available with or without Molift Scale. Molift Scale is approved Class III. The scale can also calculate BMI (Body Mass Index). 2-point aluminum sling bar 2-point, Small, aluminium, width = 350 mm Art.no: 1430117 Art.no: 1430120 (Incl.
Molift Mover 205 / www.etac.com Maintenance Cleaning and disinfection Reconditioning Clean on a regular basis. Clean surfaces with a damp cloth using an appropriate pH-neutral detergent. Do not use solvents or strong liquids, this may damage surfaces on the lifter. For disinfection when needed; use isopropyl alcohol. Avoid abrasive cleaning products. Remove hair and pile from the castors and verify that the castors rotates freely.
Molift Mover 205 / www.etac.com Troubleshooting Symptom Possible cause / action The lifting column is wobbly The lifting column is not correctly positioned in the chassis or the locking handle is not fully locked. Assemble column and chassis properly. The lifter moves unevenly on a plane surface The castors move unevenly because of pile and dust. Clean the castors. Remove hair and dirt. The lifting arm or adjustable legs moves Short circuit between hand control and lifter. uncontrolled.
Etac A/S Parallelvej 3 DK-8751 Gedved www.etac.
