Circuit Diagramm

mm
IN
73251-2202
.110
GOLD FLASH/STANDARD TRAY W/O WASHER AND NUT
2.79
2.79
MIN6.10
.240
73251-2201
73251-2201 PACKAGED IN SMALL TRAY (20 CAVITY)
2.79
0.50 ± 0.15
.020 ± .006
.110
3.94
MATERIALS AND FINISHES:
BODY, JAM NUT: BRASS
FINISH: SEE TABLE
CENTER CONTACT: BERYLLIUM COPPER
PLATED GOLD
INSULATOR: TEFLON
LOCKWASHER: PHOSPHOR BRONZE
FINISH: SEE TABLE
DIM A
DIM A
± 0.15
± 0.006
73251-2205
73251-2200
73251-2204
SPECIFICATION
6.35 ± 0.15
.250 ± .006
2.79
LOCKWASHER
2.79
16.50 ± 0.30
.650 ± .012
PLATING (BODY, NUT, LOCKWASHER) AND PACKAGING
RECOMMENDED PANEL CUTOUT
2.79
73251-2208
0.50 ± 0.20
.020 ± .008
PS-89675-3460
11.43 ± 0.15
.450 ± .006
.110
.110
GOLD / STANDARD TRAY
73251-2207
RECOMMENDED PCB LAYOUT
TYP2.54
.100
.110
TYP5.08
.200
.110
DIM A
DESCRIPTION
9.60 ± 0.20
.378 ± .008
⌀
73251-2203
.155
73251-2206
3.94
GOLD FLASH / STANDARD TRAY (54 CAVITY)
1.93 ± 0.20
.076 ± .008
MIN
5 PLACES
1.50
.059
⌀
SEE SD-73251-496 FOR PART NO. CONTINUATION
.110
10.44 ± 0.15
.411 ± .006
19.55 ± 0.25
.770 ± .010
SQ
7.00 ± 0.15
.276 ± .006
SAME AS 73251-2201 EXCEPT COMMERCIAL CONTACT
73251-2201 PACKAGED ONE PER BAG
.110
GOLD FLASH / STANDARD TRAY
HEX
8.00 ± 0.20
.315 ± .008
JAM NUT
PART NO.
73251-2209
ELECTRO/MECH PERFORM.
.155
GOLD FLASH/STANDARD TRAY W/O WASHER AND NUT
NICKEL / STANDARD TRAY
2.79
2.79
SAME AS 73251-2200 EXCEPT COMMERCIAL CONTACT
⌀ 6.50
.256
12
SQ
4 PLACES
1.00 ± 0.10
.039 ± .004
⌀ 1.27 ± 0.05
.050 ± .002
D13
ADD TOLERANCE FOR DIMENSIONS PER EWR12457-A
D12
ADD TESTING ITEM OF PRODUCT SPEC ON DRAWING
REVISION DESCRIPTION
ELECTRICAL REQUIREMENTS:
1. VOLTAGE STANDING WAVE RATIO
1.1(MAX) @0-6GHz.
1.5(MAX) @6-12GHz.
1.8(MAX) @12-18GHz.
2. RF INSERTION LOSS:
0.1(MAX) @0-6GHz.
0.4(MAX) @6-12GHz.
0.7(MAX) @12-18GHz.
SMA JACK
INTERFACE
12
1/4-36 UNS-2A
11
11
10
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
CURRENT REV DESC:
EC NO:
604333
DRWN:
CWEI02
2018/09/06
CHK'D: YCHENG
2018/09/17
APPR:
YCHENG
2018/09/17
INITIAL REVISION:
DRWN:
AROBERTSON
2012/11/21
APPR: JWIENER
2012/11/21
THIRD ANGLE PROJECTION DRAWING SERIES
C-SIZE
73251
SMA JACK, R/A PCB 50 OHM
SMA-J/RA/PCB EWR-2144
PRODUCT CUSTOMER DRAWING
DOCUMENT NUMBER DOC TYPE DOC PART REVISION
SD-73251-220
PSD
000
D13
MATERIAL NUMBER
CUSTOMER SHEET NUMBER
SEE TABLE GENERAL MARKET 1 OF 1
DIMENSION UNITS SCALE
mm
NTS
GENERAL TOLERANCES
(UNLESS SPECIFIED)
ANGULAR TOL
±
°
4 PLACES
±
3 PLACES
±
2 PLACES
±
1 PLACE
±
0 PLACES
±
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
FORMAT: master-tb-prod-C
REVISION: H
DATE: 2018/01/18
SYMBOLS
=
0
=
0
=
0
=
0
=
0
=
0
=
0
=
0
=
0
DOCUMENT STATUS
P1
RELEASE DATE
2018/09/17 09:04:08
C
10
9
9
H
8
H
8
G
7
G
7
F
6
F
6
E
5
E
5
D
4
D
4
C
3
C
3
B
2
B
2
A
1
A
1