Circuit Diagramm

ManualsBrandsMolex ManualsConnectorsMOL DataCom & Specialty SMA connector Socket 50 Ω 1 pc(s) Bag

REF.223

5.66

REF

GROUNDING

RING OUTER

DIAMETER

.170

4.32

⌀

REF

GROUNDING

RING INNER

DIAMETER

.101

2.57

⌀

REF

INSULATOR

OUTER

DIAMETER

.088

2.24

⌀

REF

INSULATOR

INNER

DIAMETER

.037

0.94

⌀

MATERIALS AND FINISHES:

BODY: STAINLESS STEEL

PLATED: PASSIVATE

CENTER CONTACT: BERYLLIUM COPPER

PLATED: GOLD (50µ-in) MIN

OVER NICKEL (100µ -in) MIN

INSULATOR: PTFE

SCREW: STAINLESS STEEL

PLATED: PASSIVATE

REF.0025

0.064

CENTER CONTACT

.020

.001

0.508

0.025

⌀

.005

+.003

-.000

0.13

+0.08

-0.00

2 PLACES

THRU

.063

.001

1.600

0.025

⌀

.282

.002

7.16

0.05

2 PLACES

.141

.002

3.58

0.05

REF

GROUND PAD

MINIMUM

.170

4.32

⌀

GROUND PAD

.101

.002

2.57

0.05

⌀

SIGNAL PAD

.030

.003

0.76

0.08

⌀

GENERAL PCB LAYOUT

REF.625

15.88

⌀

REF.282

7.16

⌀

REF.102

2.59

⌀

0-80 UNF

2 PLACES

REF.481

12.21

⌀

DETAIL C

DETAIL D

REF.065

1.65

.376 REF

9.55

GROUNDING RING

SMA JACK

INTERFACE

1/4-36 UNS-2A

MOUNTING SCREWS MUST NOT

EXTEND BEYOND THIS POINT

GROUND

PAD

SIGNAL PAD

.218 MIN

5.54

.093 MAX

2.36

SEE SHEET 2 FOR PART NUMBERS

CURRENT REV DESC: SEE ECM 117632

EC NO:

174360

DRWN:

PSWAMI02

2018/04/04

CHK'D:

PSWAMI02

2018/04/04

APPR:

AROBERTSON

2018/04/04

INITIAL REVISION:

DRWN:

PSWAMI02

2017/06/01

APPR:

AROBERTSON

2017/06/01

THIRD ANGLE PROJECTION

DRAWING SERIES

C-SIZE

73251

DIMENSION UNITS

SCALE

INCH

GENERAL TOLERANCES

(UNLESS SPECIFIED)

INCH

4 PLACES

± ±

3 PLACES

± ±

2 PLACES

± ±

1 PLACE

± ±

0 PLACES

± ±

ANGULAR TOL

DRAFT WHERE APPLICABLE

MUST REMAIN

WITHIN DIMENSIONS

THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION

SMA JACK, 2H FLG WITH

0-80 THD, 50 OHM 27 GHZ SMA-JR/F, EWR-10959-A

PRODUCT CUSTOMER DRAWING

DOCUMENT NUMBER

DOC TYPE DOC PART REVISION

SD-73251-185

PSD

000

B21

MATERIAL NUMBER

CUSTOMER

SHEET NUMBER

SEE TABLE 1 OF 3

FORMAT: IN-master-tb-prod-C

REVISION: C

DATE: 2018/01/18

DOCUMENT STATUS

RELEASE DATE

2018/04/04 13:36:29

PS-89675-3460 ELECTO/MECH PERFOR

MIL-STD-348B, FIG 310-2 INTERFACE

SPECIFICATION DESCRIPTION

Summary of content (3 pages)

PAGE 1
2 11 10 9 MATERIALS AND FINISHES: H 7 8 .376 REF 9.55 BODY: STAINLESS STEEL PLATED: PASSIVATE 5 6 2 1 H ⌀ .102 REF CENTER CONTACT: BERYLLIUM COPPER PLATED: GOLD (50µ-in) MIN OVER NICKEL (100µ -in) MIN 2.59 1/4-36 UNS-2A INSULATOR: PTFE GROUNDING RING G 3 .223 REF 5.66 .065 REF 1.65 .093 MAX 2.36 4 C SCREW: STAINLESS STEEL PLATED: PASSIVATE G ⌀ .481 REF D SMA JACK INTERFACE F ⌀ .282 REF ⌀ .625 REF 12.21 7.16 15.88 F .218 MIN 5.
PAGE 2
12 11 10 9 8 7 5 6 4 3 2 1 MATERIALS AND FINISHES H SEE SHEET 1 H PCB LAYOUT SEE SHEET 1 B B PCB RANGE SEE TABLE G .218 MIN 5.54 +.000 -.031 .00 A -.79 SCREW LENGTH SEE TABLE A G F F ⌀ .116 +.000 -.012 2.95 E 0.00 -0.30 E 0-80 UNF-2A THREAD TORQUE TO .5-.8 INCH-POUNDS +.002 -.006 +0.05 1.06 -0.15 .042 D C B D 73251-1856 73251-1855 73251-1854 73251-1853 73251-1852 73251-1851 73251-1850 PART NO. 4.76 / .188 3.18/ .125 9.53/ .375 6.35/ .250 N/A 4.76/ .188 N/A (MM/IN) DIM A .
PAGE 3
12 11 10 9 8 7 5 6 4 3 2 1 ADDITIONAL APPLICATION NOTES / ASSEMBLY INSTRUCTIONS H H 1. SEE SHEET ONE FOR SUGGESTED PCB LAYOUT. HEIGHT OF GROUND AND SIGNAL PADS MUST BE EVEN WITHIN ±.0015(.038). G G 2. SECURE CONNECTOR TO BOARD BY THREADING TWO 0-80 SCREWS FROM BOTTOM SIDE OF BOARD THROUGH CONNECTOR HOLES TO INDICATED TORQUE (SEE FIGURE). PCB DO NOT SOLDER CONNECTOR TO BOARD. F F TORQUE SCREWS TO .5 - .8 INCH-POUNDS TWO PLACES E E D D .218 MIN 5.