Datasheet
Hand Crimp Tool for SL Crimp Terminals
Doc No. ATS-638118700 Release Date: 07-30-07 UNCONTROLLED COPY Page 2 of 8
Revision: E Revision Date: 11-09-17
INSULATION
CRIMP
BRUSH
STRIP
LENGTH
BELL MOUTH
CRIMP HEIGHT
BEND
DOWN
BEND UP
ROLLING
CONDUCTOR
CRIMP
TWISTING
DEFINITION OF TERMS
The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope.
CONDITIONS
After crimping, the conductor profiles should measure the following:
Terminal
Series No
Wire Size
Conductor Crimp
Insulation Crimp
Pull Force
Minimum
Profile
Height (Ref.)
Width (Ref.)
Height (Ref.)
Width (Ref.)
AWG
mm
2
mm
In.
mm
In.
mm
In.
mm
In.
N
Lb.
2
2
-
24
32
-
36
50084
22
0.33
0.75
-
0.85
.030
-
.033
1.43
.056
1.70
.067
1.76
.069
39.2
8.82
X
24
0.20
0.75
-
0.85
.030
-
.033
1.43
.056
1.70
.067
1.76
.069
29.4
6.61
X
32
0.03
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
4.4
1.00
X
34
0.02
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
2.6
0.60
X
36
0.01
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
1.8
0.40
X
50088
22
0.33
0.75
-
0.85
.030
-
.033
1.43
.056
1.70
.067
1.76
.069
39.2
8.82
X
24
0.20
0.75
-
0.85
.030
-
.033
1.43
.056
1.70
.067
1.76
.069
29.4
6.61
X
32
0.03
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
4.4
1.00
X
34
0.02
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
2.6
0.60
X
36
0.01
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
1.8
0.40
X
70021
22
0.33
0.75
-
0.85
.030
-
.033
1.43
.056
1.70
.067
1.76
.069
39.2
8.82
X
24
0.20
0.75
-
0.85
.030
-
.033
1.43
.056
1.70
.067
1.76
.069
29.4
6.61
X
32
0.03
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
4.4
1.00
X
34
0.02
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
2.6
0.60
X
36
0.01
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
1.8
0.40
X
70058
22
0.33
0.75
-
0.85
.030
-
.033
1.43
.056
1.70
.067
1.76
.069
39.2
8.82
X
24
0.20
0.75
-
0.85
.030
-
.033
1.43
.056
1.70
.067
1.76
.069
29.4
6.61
X
32
0.03
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
4.4
1.00
X
34
0.02
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
2.6
0.60
X
36
0.01
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
1.8
0.40
X
71851
22
0.33
0.75
-
0.85
.030
-
.033
1.43
.056
1.70
.067
1.76
.069
39.2
8.82
X
24
0.20
0.75
-
0.85
.030
-
.033
1.43
.056
1.70
.067
1.76
.069
29.4
6.61
X
32
0.03
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
4.4
1.00
X
34
0.02
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
2.6
0.60
X
36
0.01
0.53
-
0.63
.021
-
.025
0.91
.036
0.95
.037
1.16
.046
1.8
0.40
X
To Achieve IPC
-
A
-
620 Class 2 Crimps, the following overall wire insulation diameter ranges are recommended:
1. Profile 22-24: 1.30-1.65mm (.051-.065 inch)
2. Profile 32-36: 0.50-0.64mm (.020-.025 inch)
CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects because
damage can occur to the tool or die.