Datasheet

CONFIGURATIONS
2
BACKSHELL
8
2X10 CONNECTOR INTERFACE DEFINITION
7
BACKSHELL CONFIGURATIONS
NOTES: VALID UNLESS OTHERWISE SPECIFIED
1. GENERAL:
a. APPLICATION SPECIFICATION SEE: AS-33472-100
-CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY,
CONNECTOR ASSEMBLY, PACKAGING INFORMATION, CONNECTOR
MATING, SERVICE INSTRUCTIONS, ELECTRICAL CONTINUITY
CHECKING, CRIMPING, AND TROUBLESHOOTING.
-DESIGNED TO MATE WITH DEVICE OR CONNECTOR AS SPECIFIED
IN THE MATING INTERFACE/CONNECTOR DRAWINGS CHART.
*DENOTES DRAWINGS THAT CAN BE ACCESSED AT <http://ewcap.uscarteams.org/>.
-ASSEMBLY SHIPPED WITH PLR IN PRE-LOCK POSITION
(SEE PLR PRE-LOCK VIEW SHEET 5).
b. PRODUCT SPECIFICATION SEE:
-STANDARD CONFIGURATION (STD): PS-33472-000
-TRANSMISSION CONFIGURATION (TRNS):
CONTAINS SILICONE: TS-160038-0001
SILICONE FREE: TBD
-UL V0 CONFIGURATION (UL V0): TBD
CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY,
RATINGS (CURRENT, TEMPERATURE, SEALING, AND FLAMMABILITY),
TERMINALS, WIRE DIAMETER RANGE, PRODUCT VALIDATION, AND PRODUCT DEVIATIONS.
c. PACKAGING SPECIFICATION PER MOLEX DRAWING: SEE PACKAGING CHART
d. PARTS MUST BE IN COMPLIANCE TO MOLEX CHEMICAL SUBSTANCES FOR
PRODUCTS AND PACKAGING SPECIFICATION: QEHS-699000-301
e. DATA MUST BE SUBMITTED UNDER THE MOLEX PART NUMBER TO IMDS
(COMPANY ID#13255)
2. DESIGN - MATERIALS:
a. FOR BILL OF MATERIALS SEE:
-STANDARD CONFIGURATION SD-33472-0002
-TRANSMISSION CONGURATION
CONTAINS SILICONE: SD-160038-0002
SILICONE FREE: SD-160092-0002
-UL V0 CONFIGURATION SD-160074-0002
b. TRANSMISSION CONNECTOR COMPONENTS MUST MEET THE MATERIAL REQUIREMENTS
SPECIFIED IN TS-160038-0001 & TBD
3. DESIGN - GEOMETRY:
a. THE 3-D CAD DATA IS BASIC (WITHOUT TOLERANCE) AND MASTER FOR THIS PART
WITH THE EXCEPTION OF UNDERLINED DIMENSIONS. DIMENSIONAL INFORMATION NOT SHOWN
ON THIS DRAWING IS DEFINED BY THE DATA FILE AT ITS LATEST REVISION.
b. GEOMETRIC DIMENSIONS AND TOLERANCES PER ASME Y14.5M-2009
c. EDGES AND UNDIMENSIONED DETAILS PER ISO13715
d. CORNERS SHOWN AS SHARP TO BE R 0.2 MAX.
e. LETTERING SHALL BE 0.15 MAX RAISED IN 0.25 MAX RECESS PAD.
THIS INCLUDES RECYCLING CODE, CAVITY ID, VENDOR IDENTIFICATION,
AND CUSTOMER MATERIAL NUMBER.
f. VISUAL DEFECTS SHALL MEET COSMETIC STANDARD PS-45499-002 (Class B).
g. LASER MARKING:
1. PART NUMBER
2. DAY OF THE YEAR
3. SHIFT
4. YEAR
FOR ADDITIONAL INFORMATION SEE SECTION 5 UNDER PROCEDURES IN ES-34735-008.
h. 2X2 CLIP-SLOT DESIGN IS BASED ON USCAR/EWCAP 7mm CLIP SLOT EWCAP - 005 - 7
2X3 THRU 2X10 CLIP-SLOT DESIGN IS BASED ON USCAR/EWCAP 11mm CLIP SLOT EWCAP - 005 - 11
BACKSHELL NOTES
TABLE OF CONTENTS
SHEET DESCRIPTIONSHEET NO.
1
3-4
5
6
NOTES AND BOM
KEY CONFIGURATIONS
RECEPTACLE CONNECTOR ASSEMBLY
9
B
*150-S-012-2-Z01 SD-33482-0001
UL V0 2X6
N/A
*150-S-006-2-Z02TRANSMISSION 2X3
PK-31300-903
PK-31300-903
PK-31300-903
2X3
2X2
2X4
2X6
2X8
DESCRIPTION
2X10
PK-31300-903
PK-31300-903
PK-31300-635
DRAWING NO. INTERFACE DEFINITION
SD-33472-0001
*150-S-004-2-Z02
*150-S-008-2-Z02
*150-S-012-2-Z01
*150-S-016-2-Z01
*150-S-006-2-Z02 SD-33482-0001
SD-33482-0001
SD-33482-0001
SD-33482-0001
SD-33482-0001
SD-33482-0001
MOLEX INLINE
STANDARD 2X10
DESCRIPTION
STANDARD 2X8
STANDARD 2X6
STANDARD 2X4
STANDARD 2X2
STANDARD 2X3
MATING INTERFACE/CONNECTOR DRAWINGS
UL V0 2X2
SD-33482-0001*150-S-004-2-Z02
UL V0 2X4
SD-33482-0001*150-S-008-2-Z02
UL V0 2X10
SD-33482-0001SD-33472-0001
2x8
2x10
2x6
2x4
2x3
2x2
C2
ADDED MOLEX BACKSHELL DETAILS
C1
ADDED 2X6-TRNS.-WITH/WITHOUT CLIPSLOT *
C ADDED 2X10-STD.-WITH CLIPSLOT *
B3
ADD ROW FOR 2X6 V0 ON SHEET 5DIM3#
UPDATE TO 25.0 MAX FOR V0DIM11#
UPDATE TO 33.85 MAX FOR V0
B2
ADD 2X6 UL V0 CONFIGURATIONS
B1
UPDATE 2X6 W/O CLIPSLOT DIM G ON
TABLE OF SHEET 5
B
ADDED 2X2 - STD- WITH CLIPSLOT,
2X8 - STD- WITH CLIPSLOT
AND NOTE h
A11
MINOR GEOMETRY CHANGE FOR UL V0
A10
UPDATED 2X4 DRAWING NUMBER
A9
UPDATED 2X10 PART NUMBERS
A8
UPDATED 2X3 DRAWING NUMBER
A7
UPDATED 2X10 INTERFACE
A6
ADDED TRANSMISSION REFERENCES
A5
ADD 2X10 INTERFACE SHEETS
A4
ADD UL V0 CONFIGURATIONS
A3
ADDED 2X3 STD AND TRANSMISSION
A2
UPDATED 2X8 BLD DRAWINGS
A1
FIXED TYPO IN NOTE 1a, UPDATED 2X6
MOLEX INLINE BLADE DRAWING
A
INITIAL RELEASE
REV
REV DESCRIPTION
INSPECTION NUMBER LOG
LAST NUMBER: 11
ADDED: 11
REMOVED:
C
B
C1
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
CURRENT REV DESC:
EC NO:
171650
DRWN: DDEB
2018/01/19
CHK'D: MVANSLAMBROU
2018/02/16
APPR:
MVANSLAMBROU
2018/02/16
INITIAL REVISION:
DRWN:
APROFFITT
2014/05/14
APPR:
VKOSHY
2014/06/27
THIRD ANGLE PROJECTION DRAWING SERIES
A1-SIZE
33472
DIMENSION UNITS SCALE
mm
1:1
GENERAL TOLERANCES
(UNLESS SPECIFIED)
ANGULAR TOL
±
1.0 °
4 PLACES
±
3 PLACES
±
2 PLACES
±
0.1
1 PLACE
±
0.2
0 PLACES
±
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
MX150 RCPT
DUAL ROW SEALED ASSEMBLY MAT SEAL
PRODUCT CUSTOMER DRAWING
DOCUMENT NUMBER DOC TYPE DOC PART REVISION
SD-33472-0001
PSD
001
C2
MATERIAL NUMBER
CUSTOMER SHEET NUMBER
GENERAL MARKET 1 OF 11
SYMBOLS
=
0
=
0
=
0
=
0
=
0
=
0
=
0
=
0
=
0
FORMAT: master-tb-prod-A1
REVISION: H
DATE: 2017/10/06
DOCUMENT STATUS
P1
RELEASE DATE
2018/02/16 22:02:25
C
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
18
18
A A
B B
C C
D D
E E
F F
G G
H H
J J
K K
L L