Circuit Diagrams
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
CURRENT REV DESC:
EC NO:
631014
DRWN:
NVENKATESHSH
2019/05/11
CHK'D:
ADHIR
2020/03/06
APPR:
ADHIR
2020/03/06
INITIAL REVISION:
DRWN:
LPULLIAM
2006/01/31
APPR:
bmoser
2006/02/02
THIRD ANGLE PROJECTION
DRAWING SERIES
C-SIZE
33000
MX150 1.5MM BLADE
TERMINAL
PRODUCT CUSTOMER DRAWING
DOCUMENT NUMBER
DOC TYPE
DOC PART
REVISION
SD-33000-001
PSD
001
D2
MATERIAL NUMBER
CUSTOMER SHEET NUMBER
SEE TABLE GENERAL MARKET 3 OF 5
DIMENSION UNITS
SCALE
mm
2:1
GENERAL TOLERANCES
(UNLESS SPECIFIED)
ANGULAR TOL
±
3.0 °
4 PLACES
±
3 PLACES
±
2 PLACES
±
0.10
1 PLACE
±
0.3
0 PLACES
±
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
FORMAT: master-tb-prod-C
REVISION: H
DATE: 2018/01/18
SYMBOLS
=
0
=
0
=
0
=
0
=
0
=
0
=
0
=
0
=
0
DOCUMENT STATUS
P1
RELEASE DATE
2020/03/06 02:34:08
C
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
A A
B B
C C
D D
E E
F F
G G
H H
19.05
2.00 (2)
R 1.45
ANVIL
BREAK SHARP
EDGE BY HAND
2 PLCS. (R 0.10)
0
45
°
X 0.50 (8)
10.35
21.70
12.167
6.35
BLOCK
00
11.3
30.48
6.93
CENT. TO 2.600
0.919 SLOT
13.987
15.05
19.05
6.35
10.35
25.4
15.05
front1
0
14.242
BREAK SHARP
EDGE BY HAND
2 PLCS. (R 0.10)
BREAK SHARP EDGE
AROUND OPENING
(R 0.10)
12.970
11.081
0
PUNCHES
0
TERMINAL
0
6.35
19.05
0
CRIMP TOOLING
SCALE 2:1
(1.85 )
DR. & C'BORE
FOR A 4MM S.H.C.S.
(2)
KNOCK DOWN
(ADJUST TO MAINTAIN
STRAIGHT CRIMP)
6.35
25.4
19.05
25.4
6.35
45
°
X 0.50 (8)
(4)
45
°
X 0.3
3.161
1.900
0
11.737
SEE Detail1
4MM TAP
(2)
11.737
(0.150 )
12.687
(3)
14.242
R 0.20
11.081
1.052
12.167
CAP
CAP
2.550
Detail1
SCALE 10:1
(4)
INSPECTION SLOT
25.4
13.987
2.600
0.178
BLOCK
7.05
CHECKING AID TOLERANCE
.XXX = .005
.XX = .03
.X = .3
CHECKING-AID
2 PIECE ASM. A2 TOOL STEEL
HARDEN & GRIND TO A ROCKWELL
HARDNESS "C" SCALE OF 56-58
CRIMP REQUIREMENTS:
1. CRIMP STRAIGHTNESS MUST BE MAINTAINED.
USE A KNOCKDOWN TOOL LOCATED AS SHOWN.
TERMINAL BOX MUST NOT BE DEFORMED
2. AFTER CRIMPING, THE TERMINAL AND WIRE MUST FIT FREELY
INTO THE CHECKING AID 33000-700. PROPER INSERTION
DEPTH IS MET WHEN BLADE TIP STOPS ON CAP. SLOTS PROVIDED
TO VISUALLY INSPECT STOPAGE OF PIN TIP.
3. FOR OTHER MECHANICAL REQUIREMENTS ON CRIMPED TERMINALS,
REFER TO SAE/USCAR-21 (5-13-02) SECTIONS 4.2
(VISUAL INSPECTION), 4.3 (CROSS SECTION ANALYSIS)
AND 4.4 (CONDUCTOR CRIMP PULLOUT FORCE)