User's Guide

AirTight Management Console Configuration
125
10 b/g/n 2.457 48 a/n/ac 5.24 132 a/n/ac 5.66
11 b/g/n 2.462 50 a/n/ac 5.25 136 a/n/ac 5.68
12 b/g/n 2.467 52 a/n/ac 5.26 140 a/n/ac 5.7
13 b/g/n 2.472 56 a/n/ac 5.28 149 a/n/ac 5.745
14 b/g/n 2.487 56 a/n/ac 5.28 152 a/n/ac 5.76
184 a/n/ac 4.92 58 a/n/ac 5.29 153 a/n/ac 5.765
188 a/n/ac 4.94 60 a/n/ac 5.3 153 a/n/ac 5.765
192 a/n/ac 4.96 64 a/n/ac 5.32 157 a/n/ac 5.785
196 a/n/ac 4.98 100 a/n/ac 5.5 160 a/n/ac 5.8
208 a/n/ac 5.04 104 a/n/ac 5.52 161 a/n/ac 5.805
212 a/n/ac 5.06 108 a/n/ac 5.54 161 a/n/ac 5.805
216 a/n/ac 5.08 112 a/n/ac 5.56 165 a/n/ac 5.825
Radio Settings
SS-300-AT-C-50, SS-300-AT-C-55, SS-300-AT-C-60 and SS-300-AT-O-70, C-75 and C-65 devices can
function in access point mode as well as in sensor mode.
When in AP mode, a single physical AP device can be logically split up into multiple virtual APs. You can
configure the radio settings and specify one or more Wi-Fi profiles if you configure the AirTight device to
function as an AP. Each SSID profile corresponds to and represents the configuration settings of one
virtual AP. You can configure up to 8 virtual APs on one radio.
If you want the AirTight device to function as a mesh AP, you must define and add a mesh profile to the
device template. Dual-radio AirTight device models like SS-300-AT-C-55, SS-300-AT-C-55-E, SS-300-
AT-C-60, SS-300-AT-O-70, C-75, C-75-E, and C-65 are capable of functioning as mesh APs. An AirTight
device that functions as a mesh AP cannot function in WIPS mode. Therefore, at a given point, a device
can have one or more Wi-Fi profiles attached to it or a single mesh profile attached to it. Both Wi-Fi profile
and mesh profile cannot be attached to a radio at the same time.
To operate the device in the AP mode, you must configure the radio settings, and add Wi-Fi profiles to
indicate which wired network the AP should connect to. To operate the device in the WIPS sensor mode,
all you need to do is select the device model. In every model, the available radios are configured to
function as WIPS sensors. This means that on any AirTight device model, the WIPS sensor option is
selected, by default, for all available radios.
To configure radio settings for access point mode, do the following.
1.
Go to Configuration>Device Configuration>Device Templates.
2. Click Radio Settings on the Add Device Template dialog box or the Edit Device Template dialog
box, as applicable.
3.
Click Define settings for model link. A drop down list of available AirTight device models appears.
4. Select the appropriate model. The details for the model appear. To configure radio settings for the
SS-300-AT-C-55-E device, select the SS-300-AT-C-55 option. To configure radio settings for the C-
75-E device, select the C-75 option.
5.
Select the Operation Mode for the desired radio as Access Point.
6. Configure the radio settings.