Instructions for Assembly and Operation Instrucciones de montaje y funcionamiento Directives d’assemblage et d’utilisation For use with the MoJack PRO and MoJack EZ Para el uso con el MoJack PRO y MoJack EZ À utiliser avec les Mojack PRO et Mojack EZ GIVING MOWER MAINTENANCE A LIFT. ELEVE EL NIVEL DE MANTENIMIENTO DE SU CORTADORA DE CÉSPED. ÉLÈVE LES NORMES EN MATIÈRE D’ENTRETIEN DES TONDEUSES. www.theMoJack.
MoJack WorkBench Introduction This manual contains assembly, parts, operating, maintenance, adjustment and safety instructions for your MoJack WorkBench accessory. BEFORE USING YOUR MOJACK WORKBENCH, CAREFULLY READ THIS MANUAL IN ITS ENTIRETY. By following these operating, maintenance and safety instructions, you will prolong the life of your MoJack lift and accessories and promote safe operation.
MoJack WorkBench Warnings and Safety Instructions Read and understand all safety and operating instructions for the MoJack PRO or MoJack EZ Lift. Read and understand all safety and operating instructions before using the MoJack WorkBench. Never allow anyone unfamiliar with the safety or operating instructions to use the MoJack WorkBench. Follow all safety and servicing instructions provided by the manufacturer of product being lifted before using the MoJack WorkBench.
MoJack WorkBench Warranty and Returns LIMITED WARRANTY For two years for residential use and one year for commercial use MoJack warrants the product against failure due to defect in material or workmanship when product is used properly. MoJack will replace any defective part at no cost. This warranty does not cover any product that has been altered or adjusted, or any product that has been misused or abused. THIS IS THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDY.
MoJack WorkBench Parts List Item No. Qty. Description 1 1 Left Sled 2 1 Right Sled 3 2 WorkBench Insert 4 2 Sled Insert 2 1 4 3 Hardware List Item No. Qty. 5 2 Clevis Pin 6 2 Hair Pin 7 2 Cap Screw – M12-1.75 x 65 8 2 Nylock Nut – M12-1.75 Description 7 5 6 Cap Screw – M12-1.75 x 65 5 8 Clevis Pin Hair Pin Nylock Nut – M12-1.
MoJack WorkBench Assembly Instructions for use with MoJack EZ STEP 1 Remove MoJack WorkBench from package. Inventory items to be certain all parts and hardware are present. If any parts or hardware are missing, please contact MoJack at 1-877-575-3173 or email us at parts@themojack.com. STEP 2 Slide the Left and Right Sleds 1 and 2 into the Lift Arm and secure with Push Pins that are used to secure the wheel pads of the MoJack as shown.
MoJack WorkBench Operating Instructions for use with MoJack EZ STEP 1 Move push mower onto sleds • With the carrier arm fully lowered, lift the front end of the push mower onto the sleds and then move the push mower so that the front wheels of the push mower are touching the front of the sleds. • Secure the push mower to the sleds by attaching the Clevis Pin 5 and Hair Pin 6 as shown.
MoJack WorkBench Operating Instructions for use with MoJack EZ STEP 3 Raising the Mower • Raise the mower by rotating the Crank Handle clockwise. Do not attempt to lift more than 200 lbs. The MoJack must be used on a solid level surface. The mower engine must be turned off. If using the WorkBench Inserts, do not install past safety sticker. STEP 4 Raising Lift Arm to Locking Position • Raise the Lift Arm until the Carrier Locking Pin drops into the Safety Hole.
MoJack WorkBench Assembly Instructions for use with MoJack PRO STEP 1 Remove MoJack WorkBench from package. Inventory items to be certain all parts and hardware are present. If any parts or hardware are missing, please contact MoJack at 1-877-575-3173 or email us at parts@themojack.com. STEP 2 7 Cap Screw Slide Sled Inserts 4 onto Sleds 1 and 2 , and secure using Cap Screws 7 and Nylock Nuts 8 and tighten as shown.
MoJack WorkBench Operating Instructions for use with MoJack PRO STEP 1 Move push mower onto sleds • With the carrier arm fully lowered, lift the front end of the push mower onto the sleds and then move the push mower so that the front wheels of the push mower are touching the front of the sleds. • Secure the push mower to the sleds by attaching the Clevis Pin 5 and Hair Pin 6 as shown.
MoJack WorkBench Operating Instructions for use with MoJack PRO STEP 3 Raising the Mower • Raise the mower by rotating the Winch Handle clockwise. Do not attempt to lift more than 200 lbs. The MoJack must be used on a solid level surface. The mower engine must be turned off. If using the WorkBench Inserts, do not install past safety sticker. Winch Handle STEP 4 Locking Carrier into the Safety Ratchet • As the Carrier raises, the clicking sound indicates that the Safety Ratchet is functioning properly.
