LP45546 XD Lift for Lawn and Garden Tractors and EZtrak™ Mowers Instructions for Assembly and Operation Ver.
Introduction This manual contains assembly, parts, operating, maintenance, adjustment and safety instructions for your lawn and garden tractor and EZtrak™ mower lift. BEFORE USING YOUR LIFT, CAREFULLY READ THIS MANUAL IN ITS ENTIRETY. By following these operating, maintenance and safety instructions, you will prolong the life of your lift and promote safe operation.
Warnings and Safety Instructions Read and understand all safety and operating instructions before using the mower lift. Never allow anyone unfamiliar with the safety or operating instructions to use the lift. Follow all safety and servicing instructions provided by the lawn mower’s manufacturer before using the lift. Do not modify the lift in any way. Any modifications will void any and all warranties and could compromise your personal safety.
Warnings and Safety Decals CAUTION: Avoid injury! This symbol and text highlight potential hazards or death to the operator or bystanders that may occur if the hazards or procedures are ignored. NOTE: There can be additional safety information contained on parts and components sourced from suppliers that is not reproduced in this instruction manual.
Warranty and Returns LIMITED WARRANTY For two years for residential use and one year for commercial use MoJack warrants the product against failure due to defect in material or workmanship when product is used properly. MoJack will replace any defective part at no cost. This warranty does not cover any product that has been altered or adjusted, or any product that has been misused or abused. THIS IS THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDY.
Parts List Item No. Qty. Item No. Qty.
Hardware List Item No. Qty. 11 1 Cap Screw M12-1.75 X 80 12 2 Cap Screw M12-1.75 X 65 13 2 Carriage Bolt M8-1.25 X 20 14 3 Nylock Nut – M12-1.75 15 2 Nylock Nut – M8-1.25 16 4 Push Pin 17 1 Clevis Pin 18 3 Large Hair Pin Description 11 Cap Screw M12-1.75 X 80 12 Cap Screw M12-1.75 X 65 13 14 Nylock Nut – M12-1.75 15 Nylock Nut – M8-1.25 Carriage Bolt M8-1.
Assembly Instructions STEP 1 Remove jack from package. Inventory items to be certain all parts and hardware are present. If you have any questions regarding assembly, please call manufacturerat 1-877-575-3173 or email at parts@themojack.com. STEP 2 Assemble the Wheel 4 to the Base 3 by inserting Cap Screw 12 and Nylock Nut and tighten. Repeat with second Wheel. Cap Screw 12 14 Note: Do not over tighten Nylock Nut to allow the wheels to roll easily.
Assembly Instructions STEP 4 Attach the Grip Handle 7 to the Tower 1 with two Carriage Bolts 13 and two Nylock Nuts 15 . Note: Fully tighten Nylock Nuts to secure the handle to the tower. Carriage Bolt 13 Nylock Nut 15 Grip Handle 7 Tower 1 STEP 5 Push in side of handle and rotate from storage position to the operating position. Allow to seat into the locked position.
Assembly Instructions STEP 7 Slide Lift Arm Inserts 6 into both sides of the Lift Arm 2 and secure with Push Pins 16 as shown. Lift Arm 2 16 Push Pin Push Pin 16 Lift Arm Insert 6 Lift Arm Insert 6 STEP 8 Wheel Pad 5 Ready the Wheel Pads for installation by adding Support Rods 9 and Large Hair Pins 18 . 5 Large Hair Pin 18 Support Rod 9 STEP 9 Slide the Wheel Pads of the Lift Arm Inserts with Push Pins 16 .
Operating Instructions Some steps of the Operating Instructions are repeated from the Assembly Instructions. The Operating Instructions will show a full working cycle of the mower lift. Before using the mower lift, carefully read this manual in its entirety.
Operating Instructions Preparing for use (Steps 1 - 8) STEP 1 Unfolding the Mower Lift • Pull and rotate Tower Locking Pin 90 degrees to the unlocked position. • Raise the Tower by pulling up on the Grip Handle. Once the Tower is in the vertical position, lift up on the Grip Handle and drop the Tower into the Base. • Lock the Tower into place by rotating Tower Locking Pin until the pull ring retracts into the locking slot.
Operating Instructions STEP 3 Installing Lift Arm Inserts • Slide Lift Arm Inserts into both sides of the Lift Arm and secure with Push Pins. Lift Arm Push Pin Push Pin Lift Arm Insert Lift Arm Insert STEP 4 Installing Wheel Pads • Slide Wheel Pads onto Lift Arm Inserts and secure with Push Pins. Push Pin Lift Arm Insert Wheel Pad STEP 5 Preparing the handle • Push in side of handle and rotate from storage position to the operating position. Allow to seat into the locked position.
Operating Instructions STEP 6 Familiarize yourself with the jack • Practice raising and lowering the Lift Arm before attempting to lift the mower (see Steps 12 – 16 on how to raise and lower the Lift Arm). • Practice Step 17 if you intend to raise or lower the mower with a drill attachment. NOTE: Remove all front mower attachments (ballast, bumper or brush guard) that interferes with handle before using the lift. When using the lift, keep ALL bystanders at a safe distance away from the mower lift.
Operating Instructions STEP 9 Reverse Front Tires of EZtrak™ (optional – if not applicable, skip to Step 10) • In some cases, the mower deck or anti-scalping wheels will hit the Lift Arm while the mower is being raised. This is often the case if part of the deck (including the anti-scalping wheels) protrudes past the center line of the front wheels of the mower. • Rotate the front tires 180° so that they are in the reverse position.
Operating Instructions STEP 12 Raising the Mower • Raise the mower by rotating the Crank Handle clockwise. • See Step 22 for raising the mower with drill attachment. Do not exceed the lifting capacity of 500 lbs. (226 kg) front end weight. If you have a question regarding weight of your machine, please contact the manufacturer at 1-877-575-3173 or a local John Deere Dealer. If the lift Tower is leaning while lifting or lowering the mower, this indicates an overload condition. REMOVE THE MOWER IMMEDIATELY.
Operating Instructions STEP 15 Lowering the Mower • Remove wheel chocks. • Release the parking brake. • Mower must be in neutral or hydraulic drive disengaged. • Pull and hold the Carrier Locking Handle out and turn the Crank Handle counter clockwise until Wheel Pads are firmly on the ground. The Carrier Locking Handle must be pulled out until it clears the bottom Tower Hole. It may be necessary to raise the Carrier slightly to allow the Carrier Locking Handle to be pulled out.
Operating Instructions STEP 17 When raising while using the drill, USE BOTH HANDS AND GRIP FIRMLY!! Raising the jack with a power drill (optional – power drill not included) The jack can be raised or lowered by using a variable speed corded drill (7 amp minimum) or variable speed cordless drill (18V minimum). The drill will require a 3/8” square driver (NOT INCLUDED). • Remove Crank Handle by taking off the Nylon Lock Nut and Spring using 17mm wrench.
Operating Instructions STEP 19 Carrier Removing the Lift Arm • While holding the Lift Arm, remove the Hair Pin and Clevis Pin from Lift Arm. Hair Pin • Slide the Lift Arm out of the Carrier. • Store the Hair Pin and Clevis Pin in the Lift Arm to prevent loss. Lift Arm Clevis Pin STEP 20 Raise Carrier • Raise the Carrier by turning the Crank Handle clockwise until the Carrier Locking Handle drops into the top Tower Hole.
Operating Instructions STEP 21 Rotate Crank Handle to Storage position • Push in side of handle and rotate from operating position to the storage position. Allow to seat into the locked position. STEP 22 Tower Locking Pin (unlocked position) Folding the jack • Pull and rotate Tower Locking Pin 90 degrees to the unlocked position. • Raise the Tower out of the Base by pulling up on the Lift Handle and then lower the Tower.
Maintenance Schedule • Before each use, always check for any worn, loose or damaged parts on the jack. If any damaged parts are present, do not use the jack and contact MoJack at 1-877-575-3173. Crank Handle Base • Clean and oil the entire screw thread after every fifty (50) uses or at least once a year using light machine oil. Brass Bearing • Place lithium grease between the Crank Handle Base and the brass bearing after every fifty (50) uses or once a year.
Support Rod Guide for Tire Sizes 10” – 11.5” (25cm – 29cm) Tire Size 12” – 15” (30cm – 38cm) Tire Size 15.
Notes 23
