Instruction booklet Gas hob MGH 701 GB
Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance.
Contents Important Safety Information ......................................................... 4 Description of the Hob .......................................................................... 6 Instructions for the User ................................................................. 7 Operation .............................................................................................. 8 Maintenance and Cleaning .................................................................
Important Safety Information You MUST rread ead these war nings car efully befor e installing or carefully before using the hob. If you need assistance, contact our Customer Care Department on 08705 950950. I nstallation z z z z z This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editions and the IEE Wiring Regulations.
z z z z z z z z z When using the hob for a long period time, the ventilation should be improved, by opening a window or increasing the extractor speed. Do not use this hob if it is in contact with water. Do not operate the hob with wet hands. Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance.
Description of the Hob 1 4 2 3 5 1. Auxiliary Burner 2. Semi-rapid Burners 3. Triple-crown Burner 4. Rapid Burner 5.
Instructions for the User INSTALLATION Any gas installation must be carried out by a registered competent person, and in accordance with existing rules and regulations. The relevant instructions are to be found in the second section of this manual. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown.
Operation Lighting the burners For easier lighting, proceed before putting a pan on the pan support. ) z z z To light a burner: turn the relevant knob anti-clockwise to maximum position ( ), then push it down to ignite the burner. Check the flame is regular and adjust it as required. To put the flame out, turn the knob to the symbol z. If the burner does not ignite, turn the control knob to zero, and try again. If you cannot light the flame even after several attempts, check the "cap" (Fig. - lett.
Using the Wok Stand A wok stand is provided to enable you to use a round bottomed wok on the hob. The wok stand must only be used on the central burner, and should not be used with any other type of wok or pan. When fitting the wok stand, ensure the recesses in the frame fit securely onto the bars of the pan supports, as shown in the picture.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob fr om the electricity supply from supply.. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. This appliance cannot be cleaned with steam or with a steam cleaning machine. The Hob T op Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM There is no spark when lighting the gas. SOLUTION The gas ring burns unevenly. Check that the unit is plugged in and the electrical supply is switched on. Check that the RCCB has not tripped (if fitted). Check the mains fuse has not blown. Check the burner cap and crown have been replaced correctly, e.g. after cleaning.
Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: Depth: 680 mm 510 mm CUT OUT DIMENSIONS Width: Depth: 560 mm 480 mm SUPPL Y CONNECTIONS SUPPLY Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V~ 50 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse HEA T INPUT HEAT Rear Right Burner (semi-rapid) Rear Left Burner (rapid) Central Burner (Ultra rapid triple crown) Front Right Burner (semi-rapid) Front Left Burn
BURNER RAPID POSITION M A X MIN SEMI-RAPID A U X I L I A R Y TRIPLECROWN TYPE OF GAS NATURAL GAS 20 mbar VALUE = 37.78 MJ/m 3 Ws - 50.7 MJ/ m3 LPG GAS 28-30/37 mbar VALUE = 49.92 MJ/Kg NOMINALTHERMAL POWER kW MAX MIN 0.45 1.0 0.33 4.0 1.2 0.286 0.057 0.190 0.038 0.095 0.028 0.381 0.114 115 Adjust. 96 Adjust. 70 Adjust. 146 Adjust. NOMINALTHERMAL POWER kW 2.8 0.75 2.0 0.45 1.0 0.33 4.0 1.2 NOMINALFLOW RATE g/h 202 4 3.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations.
The minimum distance combustible material or a cooker hood can be fitted above the hob is 650 mm. For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S 813 Current Edition Section 7- Permitted Locations of Appliance. Installation IMPOR TANT This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a registered competent person.
On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. A) End of shaft with nut B) Washer C) Elbow Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread).
Building In B uilding over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2.
Fitting the Hob into the Worktop Carry out the building in of the hob as follows: • put the seals supplied with the hob, on the edges of the cut out: place them exactly on the front and rear edge and at 50 mm. from the side edges, as shown in the diagram, taking care that the seals meet without overlapping; • place the hob in the cut out, taking care that it is centred; • fix the hob with the relevant fixing clamps and screws, as shown in the diagram.
Electrical Connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician, e.g.
3) Connect the brown (live) wire to the terminal in the plug which is marked with the letter 'L' or coloured red. Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath. A cut off plug inserted into safety (shock) hazard. Ensure of safely safely..
Fault Finding Preliminary Electrical Systems Check Blue Brown START Isolate appliance and carry out: A: Earth Continuity check. YES NO Blue Green Yellow Brown Carry out: C: Polarity check. Carry out: D: Resistance to Earth check. Has inlet fuse blown? Electricity supply should now be satisfactory. YES NO PLUG (with cover removed) Earth Wire Green/Yellow Neutral Wire Blue SOCKET (face view) ( ) E( ) FUSE Inlet wiring faulty. Rectify any fault.
A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 W (Ohm), check all earth wires for continuity and all contacts clean and tight. B. INSULA TION CHECK INSULATION Appliance electrically disconnected, all switches ON. a) meter set on W (Ohms) x 1 scale. Test leads from L to N in appliance terminal block.
Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from ignition switches connector to ignitor unit Light burner manually Check by pass simmer adj
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. the gas tap to the MAX position and ignite. ) 1)2) Turn Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: the burner and set ) 1) Re-ignite to MIN. 2) Remove the control knob.
Conversion from Natural Gas to LPG IMPOR TANT The replacement/conversion from natural gas to LPG should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted. The gas rate is adjusted to suit.
Guarantee/Customer Service Standard G uarantee C onditions We, Electrolux, undertake that if within 12 months of the date of the purchase this Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning 0870 5 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your postcode area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www .servicefor ce.co.uk www.servicefor .serviceforce.co.
European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law.
35689-8803 01/08 R.
