Specification Sheet

Arris
™
Accessories Technical Specication
18" and 24" Towel Bar YB0818 & YB0824
Stock Numbers:
Materials:
Dimensions:
Installation Instructions:
Cleaning Instructions:
YB0818BN – 18" Towel Bar
Brushed Nickel Finish
YB0818CH – 18" Towel Bar
Chrome Finish
YB0818BL – 18" Towel Bar
Matte Black Finish
YB0824BN – 24" Towel Bar
Brushed Nickel Finish
YB0824CH – 24" Towel Bar
Chrome Finish
YB0824BL – 24" Towel Bar
Matte Black Finish
1. Position the mounting template on the wall in the desired location.
2. Using a level, align the template and tape it to the wall.
3. Drill two 1/4" holes at each mounting post location that corresponds to your
product.
4. Remove the template from the wall.
5. Disassemble screws and washers from anchors.
6. Lightly tap anchors until ush with the wall.
7. Remove mounting posts from the product assemblies by loosening each
setscrew.
8. One at a time, place each mounting plate over anchors (with "UP" facing you)
and insert screw and washer through plate into anchor.
9. Tighten screws until anchor is activated behind wall (approximately 45 turns)
and tight.
10. Position each end post with setscrews facing down and place over both
mounting posts. Tighten the setscrew at the bottom of each post.
To preserve the ne nish of this product, clean only with a soft damp cloth. Dry
well. Do not use commercial or abrasive cleaners.
Towel bar
posts are constructed of zinc. Bar is
constructed of brass.
25300 AL MOEN DRIVE • NORTH OLMSTED, OH 44070
CORPORATE HEADQUARTERS: [phone] • FAX: [phone]
INTERNATIONAL: (440 ) 962-2000 • FAX: [phone]
CUSTOMER SERVICE (USA): 800-882-0116 • FAX: [phone]
WWW.MOEN.COM
©
Copyright Moen Incorporated
Stock Number: ____________________________ Towel Bar
By Moen Incorporated
25300 AL MOEN DRIVE  NORTH OLMSTED, OH 44070
CORPORATE HEADQUARTERS: (800) 321- 8809  FAX: [phone]
INTERNATIONAL: (440) 962- 2000  FAX: [phone]
CUSTOMER SERVICE (USA): 800- 882- 0116  FAX: [phone]
WWW.MOEN.COM
Copyright Creative Specialties International Literature #BA1719
Towel bar posts are constructed of
zinc. Bar is constructed of brass.
 YB0818BN – 18” Towel Bar
Brushed Nickel Finish
 YB0818CH – 18” Towel Bar
Chrome Finish
 YB0824BN – 24” Towel Bar
Brushed Nickel Finish
 YB0824CH – 24” Towel Bar
Chrome Finish
Cleaning Instructions:
Stock Number:______________________Towel Bar
By Creative Specialties
Materials:
Installation Instructions:
Stock Numbers:
Dimensions:
18” & 24” Towel Bar
YB0818 & YB0824
Arris
TM
Technical Specification
To preserve the fine finish of this product, clean only with a soft
damp cloth. Dry well. Do not use commercial or abrasive cleaners.
1) Position the mounting template on the wall in the desired location.
2) Using a level, align the template and tape it to the wall.
3) Drill two ¼” holes at each mounting post location that corresponds to
your product.
4) Remove the template from the wall.
5) Disassemble screws and washers from anchors.
6) Lightly tap anchors until flush with the wall.
7) Remove mounting posts from the product assemblies by loosening
each setscrew.
8) One at a time, place each mounting plate over anchors (with “UP”
facing you) and insert screw and washer through plate into anchor.
9) Tighten screws until anchor is activated behind wall (approximately
45 turns) and tight.
10) Position each end post with setscrews facing down and place over
both mounting posts. Tighten the setscrew at the bottom of each
post.